Assembly Instructions; How To Assemble Your Front Baby Seat Headtube; How To Adjust The Child Seat To Your Child; How To Remove Your Baby Seat From A Bicycle - Bobike exclusive mini plus Manual De Instrucciones

1. Remove the mounting block (E) from the seat (A). In order to do that, pull
the Handle for Locking / Unlocking the seat (C) until the Blocking Legs (C1)
unlocks the Mounting Block (E). Then you will be able to pull the Mounting
Block down, disengaging it from the Steel fixing rod ends (A1).
2. Remove the 2 bolts (E3) and washers (E2) from the mounting block (E).
Use the key (E1).
3. Assembling with standard kit for Ø 22-28mm steering tubes.
First, make sure that the body of the block (E4) faces up - the word "TOP"
must face up. Then make sure that the front spacer of KIT (E5.1) is correctly
applied to the body of the Mounting Block (E4) as shown. Then offer up
the assembly to the steering tube. Next offer up the rear part (E5.2 + E5.3)
so that the block entirely surrounds the steering tube. Then insert the 2
bolts (E3) and washers (E2) into the mounting block (E). Make sure that the
mounting block (E) is tightly fixed and does not move - correct tightening
is extremely important for the child's safety. We recommend a torque of
6 N.m.
1. To place the child in the seat, first fully extend the Retention System
Harness (B), sliding all the strap adjusters (B2, B3). This makes it easier to put
the child in the seat. To put the child in the seat, open the safety buckle (B1)
of the safety Retention System Harness (B) by pressing the central button
of the Safety Buckle (B1) as indicated. After putting the child, close again
the Safety Buckle (B1) and slide the central strap adjusters (B3) so that your
child is securely restraint.
2. According to the child growth, current height and weight, you can
adjust the height of the Retention System Harness on upper strap adjusters
(B2), by pulling up or down the straps until reaching the desired height.
3. Before starting the journey, always check that the child is secured and
1. Pull the Handle for Locking / Unlocking the seat (C) until the Blocking Legs (C1) unlocks the Mounting Block (E). Then, pull the child seat upwards and
backwards to release it from the mounting block (E).
• The rider must be at least 16 years of age; Check legislation and national
regulations pertaining to this.
• Make sure that the weight and height of the child do not exceed the
maximum capacity of the seat, and check this at regular intervals. Check
the weight of the child before using the child seat. Under no circumstances
should you use the child bicycle seat to transport a child whose weight is
above the permissible limit.

ASSEMBLY INSTRUCTIONS

EXCLUSIVE MINI PLUS

HOW TO ASSEMBLE YOUR FRONT BABY SEAT HEADTUBE

ASSEMBLY INSTRUCTIONS
EXCLUSIVE MINI PLUS

HOW TO ADJUST THE CHILD SEAT TO YOUR CHILD

ASSEMBLY INSTRUCTIONS
EXCLUSIVE MINI PLUS

HOW TO REMOVE YOUR BABY SEAT FROM A BICYCLE

INSTRUCTIONS FOR USE

4. Having concluded make sure that the mounting block (E) is secure and
properly aligned with the handlebar and the wheel. The mounting block
(E) must be fitted as low as the steering tube allows.
5. To place the seat (A), pull the Handle for Locking / Unlocking the seat (C)
and simultaneously insert the two ends of the steel rod (A1) of the child
seat into the corresponding holes (E4.1) of the mounting block (E4). You
will hear a slight click when the operation is complete and you will see that
the ends of the steel rod (A1) appear beneath the mounting block (E). Make
sure the child seat is upright.
6. Then sit on the bike and make sure that steering and braking are not
affected by any component of the child seat. Also make sure that there is
enough space for the child between the seat and the handlebars.
7. Make sure you have followed and fulfilled all the instructions given.
When done so, the child bicycle seat is ready for use. IT IS MANDATORY
TO READ the following chapter on safety instructions about using
your child bicycle seat.
that the belt is snug but not so tight that it hurts the child. We recommend
that the child's helmet be put on child´s head after the belt is adjusted.
Note: Always use the restraint system.
4. Adjust the height of the footrest (D) according to the height of the child.
Pull the footrest button (D2) and position the button at the desired height,
release the button and the footrest will be fitted in the chosen hole.
5. After adjusting the footrest at the desire hight, you need also to adjust
the footrest strap (D1) to ensure the safety of the child. Detach the Feet
Strap (D1) from the footrest part, by pressing the buttom and pushing it
out. Then adjust it to the child foot and fit it again. Make sure that the
buckle is not set too narrow so it wont hurt the child.
• Do not carry a child less than 9 months of age in this child bicycle seat. To
be a passenger, the child must be able to sit up straight with the head held
upright while wearing a bicycle helmet. A doctor should be consulted if
the child's growth is questionable.
• Secure the child into child bicycle seat ensuring that all the safety belts
and straps applied firmly but not so tight as to cause discomfort to the
child. Please check the safety of the fasteners often.
5