Introduction; Machine Specifications; Electrical Connection Instructions - Amano American Sanders FloorCrafter Manual Del Operador

EN
The FloorCrafter can be used on a variety of surfaces. It is an ideal tool for wood flooring maintenance and restoration work.
Part #
Model FloorCrafter 8
Electrical Requirements
230~, 60Hz / 15.7 A, 3.7 kW
Sound Emission (Lpm)* 93.0 dB(A)
Vibration
<.15 in/s
Motor 4
ontact hee Rate 2450 rpm
Abrasive Rate
4500 ft/min
A rasi e Si e 29½ x ⅞"
Fan Flow Rate
Drum Settings
er oad rotection Magnetic Circuit Breaker
E ectric a e
perating ontro s
A u t
e e ing ontro s
Operating Wheels 80 u o ete
Weight 204 lbs.
Dimensions 3 x 13¾ x 38¾
AU I N: his machine i operate on on A
sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has
a plug as shown below.
This machine must be connected to an electrically grounded circuit in order to
protect the operator from electric shock. This machine has an approved power
cord with three conductors as well as a plug with three terminals. Connect the
u to th ee ho e ece t c e
shock, use a circuit that is protected by a ground fault circuit interrupter.
DANGER: Electrocution could occur if the machine is exposed to water or rain. Keep the machine in a dry building.
DANGER: Electrocution could occur if machine is improperly connected to the electrical system. To prevent possible electric
shock, always use a 3-wire electrical system connected to an electrical ground. For maximum protection against
e ectrica shoc use a circuit that is protected
contractor.
DANGER: Electrocution could occur if the ground pin is tampered with in any way. Do not cut, remove, or break the ground
pin Do not tr to fit a three termina p ug into a receptac e or connector od other than a three p ug receptac e
or connector od
DANGER: Electrocution could occur if the machine is used with a damaged plug or power cord. If the cords or plugs are worn
or damaged in an
E tension ords
e o o e th ee- o e exte o co
and one earthing conductor. This machine is equipped
with a power cord. When greater range is needed follow the table
to determine cable gauge of additional footage. Refer to the
ch t to the ht o exte o co
oto e to o o t ke

Machine Specifications

07104A
FloorCrafter 8, Blk
230~, 60Hz / 15.7 A, 3.7 kW
93.0 dB(A)
<.15 in/s
uct o 4
2450 rpm
4500 ft/min
29½ x ⅞"
234 CFM 234 CFM
80 lbs., 70lbs., 60 lbs. 80 lbs., 70lbs., 60 lbs.
Magnetic Circuit Breaker
0 10-3 L -20 u
e Le e / A u t
xte A u t e
e eth e 80 u o ete
204 lbs.
3 x 13¾ x 38¾
230V Electrical Connection Instructions
o x u otect o
I the out et does not fit the p ug consu t our e ectrica contractor
a ha e them rep aced
th t o
o t o
co e o e t e to co e u to

Introduction

07104B
FloorCrafter 8
230~, 60Hz / 15.7 A, 3.7 kW
93.0 dB(A)
<.15 in/s
uct o 4
2450 rpm
4500 ft/min
29½ x ⅞"
234 CFM
80 lbs., 70lbs., 60 lbs.
Magnetic Circuit Breaker
0 10-3 L -20 u 0 10-3
e Le e / A u t
xte A u t e xte
e eth e 80 u o ete
204 lbs.
3 x 13¾ x 38¾
re uenc and on e ectrica o tage sho n on the motor namep ate Ma e
t e ect c
a ground au t circuit interrupter onsu t our e ectrica
an authori ed ser ice person or e ectrician
co ucto
ee e uce
7
07202B / 07104C
FloorCrafter 8
230~, 50Hz / 16.0 A, 3.0 kW
96.2 dB(A)
2.88 m/s
uct o 3 k
2042 rpm
3750 ft/min
29½ x ⅞"
195 CFM
80 lbs., 70lbs., 60 lbs.
Magnetic Circuit Breaker
L -20 u 100 0
e Le e / A u t
A u t e xte
e eth e 80 u o ete
204 lbs.
3 x 13¾ x 38¾
e u e
56380917
rms
2
uct o
3 4 0 A 3-20 u
e Le e /
A u t e
e eth e