Installation; Electrical Connections To The Mains; Connecting Input Power; Handling And Transporting The Power Source - Saf-Fro PRESTO 300MV Instrucciones De Uso Seguridad Y Mantenimiento

EN

3 - INSTALLATION

3.1 - ELECTRICAL CONNECTIONS TO THE MAINS

IMPORTANT: BEFORE CONNECTING, PREPARING OR USING
EQUIPMENT, READ THE SAFETY PRECAUTIONS.
CAUTION: The installation of the power source must
û»Ê ·Â ·Ê¿ÅÄ·Â ·Äº Ź·Â ź»É ·Äº ÅÄÂÏ Ç˷¿ »º
persons can make this installation. The power supply
installation must be dimensioned regarding the characteristics of the
ÆÅÍ»È ÉÅËȹ» »ÉÆ»¹¿·ÂÂÏ ¹ÅĹ»ÈĿĽ ʾ» ÷οÃËà ¹ÅÄÉËûº
¹ËÈÈ»ÄÊ
This equipment does not comply with IEC 61000-3-12. If it is
connected to a public low voltage system, it is the responsibility of
the installer or user of the equipment to ensure, by consultation with
the distribution network operator if necessary, that the equipment
may be connected.
This Class A equipment is not intended for use in residential
locations where the electrical power is provided by the public low-
ÌÅÂÊ·½» ÉËÆÆÂÏ ÉÏÉʻà ¾»È» Ã·Ï ¸» ÆÅÊ»ÄÊ¿·Â º¿ ¹ËÂÊ¿»É ¿Ä »ÄÉËȿĽ
electromagnetic compatibility in those locations, due to conducted
as well as radiated disturbances.

3.2 - CONNECTING INPUT POWER

The FLEX LINE circuitry in this unit automatically adapts the power source
to the primary voltage being applied. Check input voltage available at site.
This unit can be connected to the following power supplies: 230 V single
phase or 230/400 V three phases without removing cover to re-link the
power source.
       
TO THE CEE PLUG OF THE PRIMARY CABLE OF THE UNIT, THE
      
Fig.1
SERIOUS DAMAGE TO THE EQUIPMENT MAY RESULT IF THE POWER
SOURCE IS SWITCHED OFF DURING WELDING OPERATION.
Check that the power socket is equipped with the fuse indicated in the
ȷʿĽ Æ·ʻ É»» » »¹Ê¿Ì» ¹ÅÄÉËÃÆÊ¿ÅÄ Å¼ ʾ» ÆÅÍ»È ÉÅËȹ» ¾» ÆÅÍ»È
source is designed to compensate power supply variations. For variations
ż · ͻº¿Ä½ ¹ËÈÈ»ÄÊ Ì·È¿·Ê¿ÅÄ Å¼
All manuals and user guides at all-guides.com
INSTALLATION
     

¿É »ÎÆ»¹Ê»º
EN-6
3.3 - HANDLING AND TRANSPORTING
THE POWER SOURCE
THE WELDING POWER SOURCE DO NOT WEIGHT MORE THAN
25 KG AND CAN BE HANDLED BY THE OPERATOR.
READ WELL THE FOLLOWING PRECAUTIONS.
The machine is easy to lift, transport and handle, though the following
procedures must always be observed:
1 - The operations mentioned above can be operated by the
handle of the power source.
2 - Always disconnect the power source and accessories from
main supply before lifting or handling operations.
3 - Do not drag, pull or lift equipment by the cables.

3.4 - POSITIONING AND LOCATION OF THE MACHINE

·¹» ʾ» ÷¹¾¿Ä» ÅÄ · Èà ºÈÏ ·Äº »̻ ÉËȼ·¹» ¾»Ä ÆÅÉÉ¿¸Â» ºÅ ÄÅÊ
·ÂÂÅÍ ºËÉÊ ÅÈ Åʾ»È ¿ÃÆËÈ¿Ê¿»É ÃÅ¿ÉÊËÈ» Å¿Â ÉÊ»·Ã ¹ÅÈÈÅÉ¿Ì» ½·É»É ÊÅ
»ÄÊ»È Ê¾» ÷¹¾¿Ä» ¹ÅÅ¿Ľ ·¿È ÅÍ È»¼»È·¸ÂÏ É¿Ê» ʾ» ÷¹¾¿Ä» ·¸ÅÌ» ÅÅÈ
level, for example on a suitable carriage unit.
Notes for positioning the machine:
Ensure the free circulation of the cooling air; there must be at
least 300 mm of free space in front of and behind the machine
for cooling air to circulate.
The surface inclination should not exceed 15 degrees.
Protect the machine against heavy rain and direct sunshine.
Since the inhalation of welding fumes can be harmful, ensure
ʾ» ͻº¿Ä½ ·È»· ¿É » »¹Ê¿Ì»ÂÏ Ì»Äʿ·ʻº