Handlebar Adjustment - Eurosystems MLT 03 Traducción Del Original

3 .2 3 .2
5. How to switch the engine
on: Open the fuel cap (for the engine
equipped like this), push to halway the
accelerator lever on the handlebar. If
the engine is cold, operate the starter
device on the carburetor.
*
6a. MACHINE START- UP WITH
E L E C T R I C S T A R T I N G W I T H
BATTERY: Make sure the battery is
inserted correctly on the engine. Press
the start button ("t", fig. 1.9) until the
complete ignition of the machine.
CAUTION!
Do not hold the button ("t", fig. 1.9)
after starting the machine. Do not
press the button when the machine
has started/working.
CAUTION!
When after repeated starts without
charging the battery, you will feel
difficult to start the engine: we
recommend you not to insist with re-
starting, but to recharge the battery.
If you are going on trying to re-start
the battery when it is discharged or
semi-discharged this action could
affect its life.
CAUTION!
Do not completely discharge the
battery.
3 . 3 3 . 3
6b. Bring the starter handle and
pull energetically. When the engine is
on, after some bursts/bangs, put the
starter again at rest position.
3 .4 3 .4
7. Move the gearbox lever
to the direction of the desired gear
(single/reverse gear) until the gear is
inserted.
3 .5 3 .5
8. Machine - only running
function: to engage the forward or
reverse gear, release the safety device
by pressing downwards and then pull
the clutch lever.
3 .6 3 .6
9. Running function with tool:
disconnect the safety lever rotating it
to the top then lower the tool lever. To
engage the forward or reverse gear,
release the safety device by pressing
downwards and then pull the clutch
lever. To move with the engaged tool
you need the levers (2-4,
are operated at the same time.
CAUTION: When releasing each lever
(2-4, 2.2 2.2 ) you can immediately
s t o p t h e f u n c t i o n w h i c h w a s
previously engaged.
3 .7 3 .7
10. At the end of the work: To
stop the job you need to put the throttle
handle on stop position and the engine
is switching off.
DANGER!
In case you have to face an unforeseen
and accidental obstacle, you should im-
mediately leave the two driving levers
(2-4,
2.2 2.2).
8. HANDLING AND TRANSPORT
DANGER!
Before proceeding, read and under-
stand the chapter "SAFETY INSTRUC-
TIONS" in its entirety.
With the motor off, the machine can be
moved by hand by pushing or pulling it
from the handlebar.
4 . 1 4 . 1
LIFTING:
9. STORAGE
When the machine is not going to be used
for long periods of time, it is essential to
protect the tool with anti-corrosion and
antioxidant substances.
Clean the machine of leaves and/or dirt
before storage.
DANGER!
Remove the fuel from the tank and close
the tap (if present).
Park the machine fitted with the accessory
on flat ground, removing the ignition key (if
present) and/or spark plug cap.
DANGER!
Protect the sharp parts and cover the
machine with protective sheets if neces-
sary.
4 . 2 4 . 2
When the motor cultivator is
stored without equipment (like rotava-
tor, grassland mower, cutting bar, etc..) it
should be positioned as shown in the pic-
ture. Please put under the engine the poly-
styrene you can find into the packaging or
any other support showing a vertical side
at least 14 cm height. The a.m. operation
avoids the oil to draw into the combus-
2.2 2.2
) tion chamber. Please be very careful also
when putting new oil into the engine and
to the equipment assembly/disassembly.
10. PERIODIC MAINTENANCE
DANGER!
Before proceeding, read and understand
the chapter "SAFETY INSTRUCTIONS"
in its entirety.
Keep all nuts, bolts and screws tightened
to ensure safe operation of the machine
and/or interchangeable equipment in safe
conditions.
10.1 CABLE ADJUSTMENT
4 . 3 4 . 3
Warning - wheels should start
rotating only when control lever is beyond
half travel. When lever is pulled to full ex-
tent (working position), the belt-stretcher
load spring should extend by 6 to 8 mm
approx. For above described conditions
to be reached, action is to be taken on
adjuster set close to the belt stretcher
control assembly.

HANDLEBAR ADJUSTMENT

10.2
4 . 4 a 4 . 4 a
HEIGHT ADJUSTMENT:
The height of the cultivator handlebar can
be adjusted. Before starting any work it is a
good standard operating procedure to ad-
just the handlebar to the operator's require-
ments so that the machine could be easily
handled. Loosen the handles, adjust the
handlebar according to the needed height
and tightly screw the handles up.
4 . 4b 4 . 4b
LATERAL ADJUSTMENT:
Lateral handlebar adjustment keeps the
operator from stepping on ground that has
already been hoed and from damaging
vegetation. Considering the central posi-
tion (2, 5), the handlebar support can be
further reclined for one position to the left
and right side in the following way:
1. unscrew the unblocking rod until the
handlebar support is not raising from the
teeth shown on the machine;
2. orientate the handlebar support to the
desired job position and reinsert it into the
teeth part.
3. tighten the unblocking lever in order to
tighten the whole again.
CAUTION!
The handlebar support can be screwed
up only in the 3 pre-established positions:
NO intermediate positions are allowed!
4 . 4 c 4 . 4 c
JOB POSITION ADJUSTMENT
Orientate the handlebar with the handlebar
support into the needed job position
according to the tool you are going to use.