User's Instructions; Igniting The Plaque Burner (Hob); Switching On The Oven Burner; Replacing The Most Important Components - Eurotec G4SF9 Instrucciones Para La Instalación, El Uso Y El Mantenimiento

5.
5.1 IGNITING THE PLAQUE BURNER (HOB) FIG. 3
To ignite the plaque pilot flame, press the knob (Fig. 3) turning it to the left onto the (
ignite the pilot flame. Keep the knob pressed for approximately 20 seconds; on letting go of it, the pilot flame should stay
alight, if it does not then you need to repeat the process. To ignite the burner, turn the knob onto (
on to ( ) for the minimum. To extinguish the burners, turn the knob onto (
CAUTION: For reasons of safety, on the 8 kW (large) burner, it is possible to use a pan with a maximum diameter of 380 mm;
a pan with a larger diameter would stick outside the edge of the machine and be dangerous for users.
The unit needs to be checked at least twice a year. You have to check the burner, ignition, inter-ignition, maximum and
minimum settings.
5.2

SWITCHING ON THE OVEN BURNER

Mod. G4SF9 - G6SFA9 - G6SF29-G6SF9MG
-To turn on the oven control, press the knob inserted in the thermostat (fig. 7) by turning it to the left to the (
Then push the knob down to its maximum and at the same time push the piezoelectric switch button (Fig. 7).
- The pilot flame will be seen through the holes on the oven surface; keep the knob pushed down for another 20 seconds and
then release it. If the flame dies out, repeat the operation.
- To switch on the burner, turn the knob and place it on any position between.
- To switch off the burner turn the knob back onto (
the oven off completely place the knob onto ( ) position.
IMPORTANT: before using the oven for the first time heat it up to its maximum temperature for 30 - 40 minutes keeping the
oven door closed to burn possible oil residues which could lead to unpleasant smells.
- To turn on and adjust the burner, turn the knob of the thermostat in the desired position, keeping in mind that positions 8
to 1 correspond to the oven temperature (of the above-mentioned models) of approximately:
Mod. G4SF9 - G6SFA9 - G6SF29
POS. 8 = 300°C
POS. 7 = 280°C
POS. 6 = 260°C
POS. 5 = 240°C
6.
- To turn the burner off, turn the knob to (
This should only be done by an "Authorized Service Centre"!!.
To be able to change the following components you must firstly:
- shut off the gas supply inlet valve
- remove the knobs
- take off the front panel
- if necessary, remove the grills, burner lids and burners.
It is now possible to replace the most important components.
A) Worktop burner thermocouple (Fig. 2)
- unscrew the nut (7) with a size-8 wrench
- unscrew the nut (Fig. 1 pos. 4) with a size-9 wrench
- install a new thermocouple of the same type, following the reverse order to disassembly
B) Worktop cock (Fig. 1)
All manuals and user guides at all-guides.com
POS. 4 = 220°C
POS. 3 = 190°C
POS. 2 = 170°C
POS. 1 = 150°C

REPLACING THE MOST IMPORTANT COMPONENTS

) position, for complete extinction to position ( 0 ).
).
). Thus the burner is turned off, put the pilot flame remains. To turn
G6SF9MG
POS.8 = 290°C
POS.7 = 260°C
POS.6 = 240°C
POS.5 = 210°C
- 27 -

USER'S INSTRUCTIONS

) symbol then press it fully in to
) for the maximum and
POS.4 = 185°C
POS.3 = 160°C
POS.2 = 150°C
POS.1 = 140°C
) symbol.
GB