Sub-Zero ICBBI-36R Instrucciones De Instalación página 10

BUILT-IN INSTALLATION INSTRUCTIONS
LEVEL THE UNIT
Once the unit is in position, extend the front
leveling legs down by turning the legs clockwise
and adjust the height. The rear height adjust-
ment can be made from the front of the base.
Use a 8 mm socket to adjust the rear rollers. Turn
the 8 mm hex bolt clockwise to raise the unit or
counterclockwise to lower it.
When the unit is leveled properly, or squared off,
door and/or drawer adjustments are less likely to
be necessary. Refer to the illustration below for
location of the rear roller base adjustment.
IMPORTANT NOTE: Be sure to reference
leveling of the unit to the floor and not to
surrounding cabinetry. This could affect the
operation of the unit, such as door closing.
INSTALL THE KICKPLATE
To install, screw the kickplate to brackets
attached to the inside surface of each roller base.
IMPORTANT NOTE: The kickplate must be
removed for servicing. The floor cannot interfere
with removal. Refer to the label mounted on the
kickplate support for height clearance.
Reinstall the grille following the instructions on
page 8. Turn power back on to the electrical
outlet.
REAR
ADJUSTMENT
FRONT
LEVELING LEG
Rear roller base adjustment
10
All manuals and user guides at all-guides.com
OVERLAY PANEL INSTALLATION
OVERLAY PANELS
If your customer has chosen an overlay design
application, make sure that the panels you are
about to install match dimensions listed in the
Overlay Panel Specifications on page 12.
IMPORTANT NOTE: The overlay panel must fit
over the door frame. The weight of each panel
assembly cannot exceed 23 kg, 34 kg for Models
ICBBI-36R, ICBBI-36RG and ICBBI-36F.
Overlay models are shipped without handle
hardware. The cabinet manufacturer or designer
will need to provide handle hardware to match
the overall decorating scheme.
To install overlay panels, first remove the door trim
molding. For side-by-side models and the upper
door for over-and-under models, insert a screw-
driver tip into the top corner slot on the handle
side and pop out the trim molding. Remove the
screws and frame. For the drawer on over-and-
under models, insert a screwdriver tip into the slot
on either side of the trim molding running along
the top of the drawer and pop out the trim
molding. Remove the screws and frame. Refer to
the illustrations below.
Door trim Over-and-under drawer trim
Sub-Zero allows a 6 mm space to slide the
backing material into place in the frame. If your
material is thicker than a 6 mm, either rout an
edge around the panel to get a proper fit or
mount the decorative overlay panel on a sheet of
6 mm thick material and insert the backing
material into the channel.
You must allow for 3 mm space between the
backer board and the decorative panel, so the
panel will slide easily into the door frame.
The illustrations below provide a cross section
view of the three panel assembly showing place-
ment of the door /drawer /grille trim and a rear
view of the three panel assembly with critical
dimensions, standard for all models.
Install the handle hardware before inserting the
panel. We recommend larger D-style pulls. The
use of small, one-piece knobs is not recom-
mended. If you use screws with thick heads, you
will need to countersink the screws into the
backer panel before sliding the assembly into
place.
Spacer Panel
3
mm Overlay Panel
6 mm Backer Panel
8 mm min
3 mm
Door/Drawer/
Grille Trim
2 mm
Overlay panels—cross
section
Slide the panel into the frame on the door. With
the panel in position, replace the frame end. Be
sure the panel is inserted completely into the
channel for proper fit and alignment.
To reinstall the trim molding on side-by-side
models and the upper door for over-and-under
models, insert the top of the trim molding into
the grooves at the top of the door and work
downward, snapping the trim molding into the
clips on the frame.
For the drawer on over-and-under models, start
at one end and move towards the opposite end,
snapping the trim molding into the clips on the
frame.
ACCESSORIES
Overlay Panel
Spacer Panel
Optional acces-
sories are available
through your
Sub-Zero dealer. To
obtain local dealer
information, visit
our website,
subzero.com.
Backer
~19
Panel
mm
3 mm 6 mm
Overlay panels—three panel
assembly