Midi Functions; Editing Midi Parameters - Roland KR103 Manual Del Usuario

KR103 Digital Intelligent Piano

MIDI functions

14. MIDI functions
MIDI is short for "Musical Instrument Digital Interface". The word refers to many things, the most obvious being a con-
nector type that is used by musical instruments and other devices to exchange messages relating to the act of making
music.
MIDI messages are transmitted and received using
three connectors and special MIDI cables:
• MIDI IN: This connector receives messages from other
MIDI devices.
• MIDI OUT: This connector transmits MIDI messages
generated on your KR103.
• MIDI THRU: This connector "echoes back" all MIDI
messages received via MIDI IN. The KR103 does not
provide a MIDI THRU connector.
Here is how to connect the KR103 to an external
sound module, sequencer, etc. When working with an
external sequencer, be sure to establish both connec-
tions and to set Local (page 50) to "Off".
KR-777/177
KR103
Out In
MIDI
Note: You don't always need two MIDI cables. Just look at
the arrows in the above illustration for deciding which
ports you need to connect the cable to.
You can also connect the KR103's USB port to a USB
port of your computer, in which case the MIDI IN and
OUT connectors are bypassed. If you choose to work
with the USB port, you may have to install the appro-
priate drivers on your computer. See the "Readme"
files on the enclosed CD-ROM for details.
Caution
The KR103 only transmits "realtime" MIDI data. Thus,
only the notes you play on the keyboard as well as the
pedal data are transmitted (but not the Arranger or
Recorder data).
Note: The KR103 does not receive SysEx messages when the
Recorder is being used.
Each time you play on the KR103's keyboard, your Digi-
tal Intelligent Piano transmits MIDI data to its MIDI OUT
socket (or USB port). If you connect the MIDI OUT
socket to the MIDI IN socket of another instrument,
that instrument may play the same notes as one of the
KR103's parts, select sounds, etc.
Note: The KR103 receives on all MIDI channels assigned to the
various parts.
The KR103 contains the following MIDI parameters,
which are part of the Function group. Here is how to
select them and what they mean:
50
External MIDI device
External MIDI device

Editing MIDI parameters

You can edit the KR103's Function parameters via the
display. Here is a general outline of the procedure for
all parameters discussed below:
(1) Press the [Function] button (its indicator must
light).
Function
Volume Brilliance
(2) Use [√][®] to select the parameter you wish to edit
(see below).
MIDI parameters
G Local—(On/Off, Default setting: On) The Local parame-
ter allows you to establish or remove the connection
between the KR103's keyboard and the internal tone
generator.
When set to "ON" (default), playing on the KR103's key-
board will cause the corresponding notes to sound. If
you select "OFF", the corresponding MIDI messages are
no longer sent to the internal tone generator – but they
are still transmitted to the MIDI OUT port and hence to
external MIDI instruments.
Sound source
Sound source
MIDI OUT
LOCAL ON
Note: The setting of this parameter is not memorized
when you switch the KR103 off.
G TX Chnl—(1~16, Default setting: 1) This parameter
refers to the MIDI channel used for transmitting mes-
sages from the KR103 to external instruments ("TX" is
short for "transmit"). If the external instrument is set to
receive on (RX) MIDI channel 3, select "3" here. Other-
wise, the external instrument will neither play nor select
sounds, etc.
Note: MIDI messages sent from the external MIDI instru-
ment to the KR103 are received on all channels. However,
all keyboard information (of the Upper, Layer, Lower, chord,
and bass sound) will be transmitted on one channel.
For the following, always set the numbers in the same
order as they appear in the display: start with "Send
MSB" (CC00), then set "Send LSB" (CC32), and finally set
a "Send PC" value.
Part Balance Transpose Reverb
Demo
Balance
User Program
Accomp Keyboard
Sound source
Sound source
MIDI OUT
LOCAL OFF