Operations Common To Each Mode - Clarion ADZ625 Manual De Instrucciones

Radio de am/fm reproductor de cd/casetes con control de cambiador de cd/md
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

Operation Common to Each Mode
Setting the clock
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [
] button or the [
select "CLOCK_ _E".
3. Press the [
] button.
4. Press the [
] button or the [
select the hour or the minute.
5. Turn the [VOLUME] knob either clockwise or
counterclockwise to set the correct time.
∗ The clock is displayed in 12-hour format.
6. Press the [
] button to store the time into
memory.
7. Press the [T] button to return to the previous
mode.
Note:
• You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the car's
battery or take out this unit, the clock is reset. While
setting the clock, if another button or operation is
selected, the clock set mode is canceled.
Switching the spectrum analyzer
display patterns
You can select one out of 8 patterns or set it to
off.
∗ The factory default setting is "PATTERN 1".
Each time you press the [SPE/ANA] button, the
spectrum analyzer display pattern changes in the
following order:
PATTERN 1 ➜ PATTERN 2 ➜ PATTERN 3 ➜
PATTERN 4 ➜ PATTERN 5 ➜ PATTERN 6 ➜
PATTERN 7 ➜ SCAN ➜ OFF ➜ PATTERN 1...
Note:
The spectrum analyzer display is unavailable during
these operations below;
• Seek tuning and auto store in radio mode.
• Mute or pause.
• When "NO DISC" or an error message appears in
the display.
Setting the sensitivity of the
spectrum analyzer
∗ The factory default setting is "MID".
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [
] button or the [
select "ANA SENS".
20
ADZ625
3. Turn the [VOLUME] knob either clockwise or
counterclockwise to set the sensitivity of the
spectrum analyzer.
You can choose one of "LOW", "MID" or
"HIGH" for the sensitivity of the spectrum ana-
] button to
lyzer.
4. Press the [T] button to return to the previous
mode.
] button to
Setting the speed of the spectrum
analyzer display
∗ The factory default setting is "HIGH".
1. Press and hold the [T] button for 1 second or
longer to switch to the adjustment selection
display.
2. Press the [
select "ANA SPD".
3. Turn the [VOLUME] knob either clockwise or
counterclockwise to set the speed of the spec-
trum analyzer display.
You can choose one of "LOW", "MID" or
"HIGH" for the speed of the spectrum ana-
lyzer display.
4. Press the [T] button to return to the previous
mode.
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for radio or TV stations
and CDs. The numbers of titles that can be en-
tered for each mode are as follows.
Mode
Radio mode
CD mode
TV mode
CD changer mode
CDC655z connected
CDC655Tz connected
CDC1255z connected
1. Press the [FNC] button to select the mode you
want to enter a title. (radio, CD, CD changer or
TV)
∗ Titles cannot be entered for MDs with this unit.
2. Select and play a CD or a CD in the CD changer,
or tune to an appropriate TV or radio station.
3. Press the [DISP] button and display the title.
] button to
4. Press the [T] button. "TITL" appears in the dis-
play and the cursor position flashes.
] button or the [
] button to
Number of titles
30 titles
100 titles
15 titles
Number of titles
60 titles
100 titles
50 titles

Publicidad

Tabla de contenido
loading

Tabla de contenido