Concept VR3100 Manual Del Usuario página 42

EN
Before filling with water, remove the dust container
using the handle (VR3120).
Model VR3120 - Electrically operated water tank
c) Install the module:
Model VR3100, VR3110: push the module
horizontally along the back of the robot. The module
is installed in place when you hear a "click" sound.
Model VR3120: insert the dust container into the
water tank and insert the handle into the slot. Then
press and hold the button in the centre of the tank
and push it horizontally along the back of the robot.
The module is installed in place when you hear
a "click" sound.
9. Removing the wiping module
Model VR3100, VR3110: Once the robot has completed
its work, press the latches on both sides, remove the
wiping module backwards, empty the water from the
water tank and clean the cloth (do not move or flip the
robot during cleaning).
Model VR3100, VR3110 - Hanging water tank
Model VR3120: Once the robot has completed its
work, press the button in the middle of the water tank,
remove the wiping module backwards, empty the
water from the water tank and clean the cloth (do not
move or flip the robot during cleaning).
Model VR3120 - Electrically operated water tank
82
10. Instructions for using the wiping module
• Do not use the wiping module unless supervised.
• For safety, make sure the wiping module is removed
when charging or when not in use.
• Do not attempt to wipe the carpet.
• For a better wiping effect, the wiping module should
be used after sweeping or vacuuming the floor three
times.
• To refill water or clean the cloth while the appliance
is operating, pause it, remove and reinsert the wiping
module as described in steps 8 and 9. Do not move or
flip the appliance to avoid positioning errors and map
loss.
• The wiping function of the appliance is designed for
wiping and aids deep cleaning. However, it cannot
effectively remove stubborn dirt and thus replace
human power.
USE
ON/OFF
Press and hold the button for 3 seconds, the indicator
light comes on and the appliance starts.
Press and hold the button for 3 seconds while the
appliance is in standby mode, the indicator light goes out
and the appliance switches off.
NOTE: The appliance cannot be switched off while it is
being charged.
CLEANING/PAUSE
After starting the appliance, briefly press the button
the appliance or start the appliance using the mobile app
(press any button to pause the appliance).
Note:
• The robotic vacuum cleaner cannot be used to remove
fluids.
• If the battery charge level is less than 15 %, the
appliance cannot operate. In this case, recharge it.
• If the battery charge level is less than 15 %, the
appliance automatically returns to the docking station.
• Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
robot catches these wires.
CHARGING
Automatic mode: The appliance automatically returns to
the docking station after work.
Manual mode: When paused, press the button briefly
to start charging or you can use your mobile app to
charge the appliance. The indicator light flashes when the
appliance is fully charged.
VR3100 | VR3110 | VR3120
Note: If the appliance does not find the docking station,
it will automatically return to its original position. In this
case, place the device manually into the docking station.
COMPLETE AUTOMATIC CLEANING
Once the robot is on, it performs a search, generates
a map and intelligently divides it into areas. Then it sweeps
the areas one after the other properly, efficiently and
thoroughly along the wall and plans a curved / S-shaped
cleaning path. After cleaning, the robot automatically
returns to the charging base.
Note: Do not move the robot arbitrarily and often during
cleaning. After moving, place the robot in its original
position. When the robot is on again, it will try to take
a position itself. After successful positioning, the robot
will follow the planned path and continue working. If
positioning fails, the robot cancels the previous task,
creates a map, and cleans up again. Even if it does not find
a charging base.
LOCAL TURBO CLEANING
When a local area needs more thorough cleaning, the user
will identify a point on the map in the app, the device will
automatically move close to that point, take that point as
the centre, and clean the area within 1.5 x 1.5 m.
LOCAL CLEANING
If you cannot control the robot using the mobile app,
move the robot manually to the place you want to clean
up. Press the button for 3 seconds and the robot will
perform double cleaning in the area of 2 x 2 m with the
centre in its starting position.
on
ZONE CLEANING
Use the mobile app to set the size and location of the area
you want to clean up. You can set one or more areas. The
robot will clean in the areas you have set.
RESTRICTED ZONE
Use the mobile app to set up one or more restricted areas.
The robot will not clean in these restricted areas and will
clean in others.
Note: The robot may reach the restricted area due to
positioning errors, sensor errors or other reasons.
• A permanently restricted zone may be invalidated due
to a significant change in position of the charging base
and furniture. Therefore, try not to move the robot or
otherwise interfere with its work during cleaning.
• The permanently restricted area will be revoked as
soon as the map is restored.
CLEANING PLANNING
You can set a fixed cleaning time using the mobile app.
The appliance will automatically start cleaning at the
specified time and will return to the docking station when
completed.
VR3100 | VR3110 | VR3120
EN
WI-FI RESET
If the mobile phone cannot connect to the appliance
due to a change in router and password configuration
or other reasons, press the button and the button
for 3 seconds at the same time until you hear the "Wi-Fi
has been reset" voice prompt and until the indicator light
turns on blue-violet and flashes slowly.
SILENT MODE
Robot voice messages and planned cleaning will be
suppressed (inactive) during the set time.
CARPET TURBO
When the carpet is detected, the suction force
automatically increases to the highest level. WARNING -
the carpet is correctly detected only with the Carpet
brush.
SETTING THE SUCTION POWER
You can set the suction power to a quiet, standard or high
level using the mobile app.
When the carpet is detected, the suction force
automatically increases to the highest level. WARNING
- the carpet is correctly detected only with the Carpet
brush.
SETTING THE WATER FLOW (only for electrically
operated water tank of model VR3120)
You can set the water flow to a low, standard or high level
using the mobile app.
USING THE REMOTE CONTROL
1. Cleaning planning
2. Moving forward
3. Turning left
4. Local TURBO cleaning
5. Start/pause charging
6. Automatic cleaning / pause
7. Cleaning/pause
8. Turning right
9. Find the robot
10. Setting suction power / water flow
Note: To ensure that all the correct settings are effective,
you must point the remote control at the front of the
robotic vacuum cleaner from close proximity.
83