Sicherheit Und Datenschutz; Sicherheitsinformationen - ClicBot KY002CK10 Manual Del Usuario

Verbindung
Die Hotspot-Verbindung eignet sich für Szenarien, in denen kein WiFi oder ein schlechtes
WiFi-Signal vorhanden ist.
* Konfiguration der Hotspot-Verbindung:
1. Berühren Sie auf dem Bildschirm des Haupthirnmoduls (Brain) von unten nach oben,
um das Systemmenü aufzurufen. Wählen Sie dann das Gerätesymbol
klicken Sie Hotspot-Verbindung. Ein Hotspot-QR-Code wird erstellt.
2. Öffnen Sie die ClicBot App und wählen Sie das Hauptgehirnsymbol. Klicken Sie
dann die Hotspot-Verbindung, um eine Verbindung zum Internet durch Einscannen
herzustellen.
3. Scannen Sie den Hotspot-QR-Code des Haupthirnmoduls mit der Kamera des
Mobilgeräts, um eine Hotspot-Verbindung herzustellen.
Hotspot-Verbindung
Hotspot-Verbindung-Taste von Brain klicken
und den generierten QR-Code scannen
Haupthirnmodul generiert Hotspot-Verbindung-Taste von Brain klicken
Hotspot-QR-Code und den generierten QR-Code scannen
116
aus und

Sicherheitsinformationen

Any changes or modifications not
expressly approved by the party
responsible for compliance could void the
user's authority to operate the equipment.
GB19865-2005、GB6675.1-2014、GB6675.2-2014、
GB6675.3-2014、GB6675.4-2014
NOTE:This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
This device complies with part 15 of the
FCC Rules. Operation is subject to the used in accordance with the instructions,
condition that this device does not cause may cause harmful interference to radio
harmful interference (1) this device may communications. However, there is no
not cause harmful interference, and (2) guarantee that interference will not occur
in a particular installation
this device must accept any interference
received, including interference that may
cause undesired operation.

Sicherheit und Datenschutz

If this equipment does cause harmful
interference to radio or television
reception,which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
RSS-Gen Issue 4 December 2014"&"CNR-Gen 4e
the interference by one or more of the
Décembre 2014:
following measures:
--English:
--Reorient or relocate the receiving
This device complies with Industry Canada licence-
exempt RSS standard(s).
antenna.
Operation is subject to the following two conditions:
--Increase the separation between the
(1) This device may not cause interference, and (2)
equipment and receiver.
This device must accept any interference, including
--Connect the equipment into an outlet on
interference that may cause undesired operation of
a circuit different from that to which the the device.
--French:
receiver is connected.
Le présentappareilestconforme aux CNR d'Industrie
--Consult the dealer or an experienced
Canada applicables aux appareils radio exempts
radio/TV technician for help.
de licence. L'exploitationestautorisée aux deux
conditions suivantes:
The device has been evaluated to meet (1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout
general RF exposure requirement. The
brouillageradioélectriquesubi, mêmesi le
device can be used in portable exposure
brouillageest susceptible d'encompromettre le
condition without restriction.
fonctionnement.
FCC ID: 2AWR5-KY002
IC ID: 26344-KY002
117