Safety Regulations; Measures To Prevent Fires - Jotul I 80 Mini Classic Instrucciones Para La Instalación

ENGLISH
In particular, the following should be checked:
The chimney or flue system must comply with the Building
Regulations for heat producing appliances i.e. a round flue
pipe of minimum diameter 5" (125mm), a chimney size of at
least 6" (150mm) diameter, a square brick flue of at least 5
1/2" x 5 1/2" (135 x 135mm) or a factory-made system
manufactured to BS4543 and installed to BS6461.
The minimum height of the chimney must be 12' (4m). This
height should be measured from the hearth to the top of
the flue.
The chimney or flue must be free from any obstruction.
Any damper plates or flue restrictors must be removed
and no restrictor plates should be fitted. Where it is
impractical to remove dampers or restrictors, these must
be secured in the open position.
The chimney or flue must be sound and clean. If it has been
used with a wood, coal or other solid fuel fire, it must be
swept before the fireplace is installed.
Ensure that only one fireplace is served by the chimney or
flue system.
Ensure that the chimney or flue is structurally sound. In
particular, it must not be possible for products of
combustion to come into contact with combustible
materials in the structure of the building.
In some situations it may be advisable to fit a flue liner
prior to the installation of the fireplace. Your installer will
advise if this is necessary.
Note: A guide is published by the British Flue and Chimney
Manufacturers' Association which contains general
information on chimneys and flues.
If any of the pre-installation checks reveal inadequacies,
do not proceed with the installation of the fireplace until
all defects or deficiencies have been rectified.
22
All manuals and user guides at all-guides.com
Technical data for the Jøtul I 80 Mini/Maxi -
Classic, Harmony and Panorama:
Material:
Finish:
Fuel:
Max. wood length:
Air system:
Combustion system:
Flue outlet:
Flue:
Approx. weight:
Options:
Product measurements,
fireproof wall etc.:

Safety regulations

Always check your local codes in ensuring that your
installation is safe and legal.
Requirements for the floor shield: If the fireplace is to be
installed on a floor made of flammable material, the floor
beneath and in front of the fireplace must be covered by a
shield of non-flammable material (check your local codes
concerning measurements).

Measures to prevent fires

Any use of the fireplace may represent some danger.
Therefore, respect the following instructions:
• Ensure that furniture and other flammable materials
• Let the fire die. Never put it out with water as this may
• The fireplace gets warm when used and may cause
• Ash must be properly disposed of outdoors, or emptied
• Any stove should have a storage container made of non-
• You may want to keep the ash. It is a first class fertilizer
Cast iron
Paint and enamel
Wood
40 cm
Top draught and ignition vent
Air chamber for secondary
combustion
Top, rear with the use of a 100°
bend
Ø 150mm
125 kg/132 kg
Fire screen - Damper complete -
Side plate aluminium -
Grilling grid - Ash Solution -
Assembly kit for Cassette
See fig. 1
do not get too close to the fireplace. There must be a
safe distance to the product. Check your local codes.
damage the product.
burns if touched.
where it does not entail a fire hazard. Refer to local
regulations.
flammable material as a standard accessory for the
safe disposal of soot and ashes. Soot and ashes must
be stored in this container for at least a week in order
to be certain that the last ember has been extinguished.
If the container needs to be emptied before this, add
plenty of water to the container and stir.
for roses and other plants.