The Aluminium Panel; Assembly Of The Aluminium Panel; Enamelled Front Panels; Ash Compartment - Jotul I 80 Mini Classic Instrucciones Para La Instalación

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 36
ENGLISH
a washer, so that they can be pushed a little.
• Place the top grid (C) on the front frame and fasten it
with two body screws (D).
• Adjust the top grid so that it is even with the front frame.
• Loosen the two body screws (D) and remove the top
grid.
• Now the nuts which hold the cage nuts in place can be
tightened.
• Re-fasten the top grid.

The aluminium panel

If you wish to cover up any openings at the side of the
insert towards the side wall of the fireplace, black varnished
side panels made of aluminium are available. These are
700/775 mm high and are adapted to the insert which is
assembled with a top and bottom grid. If adjustment is
necessary, they are easy to cut with a bow saw or an angle
grinder.
Side panel, narrow: catalogue no: 340791/340818
breadth 76mm, height 700/775mm. (packs of 2).
Side panel, broad: catalogue no: 340792 /340817
breadth 120mm, height 700/775mm. (packs of 2).
The broad and narrow side panels can be combined to give
a total breadth of 180mm, which may also be mounted at
an angle if necessary.

Assembly of the aluminium panel

(fig. 20)
• The bracket (A) is fitted onto the side walls of the
fireplace with plugs and screws.
• Press the side panel (B) into the bracket. First put some
mortar on the base of the fireplace behind the panel,
as a support.
• If you combine the narrow and broad panels, the angle
towards the side wall of the fireplace can only be max.
70°.
Enamelled front panels (fig. 21)
• Narrow side - Catalogue no. low 340999/ high 340996
(2 units of 35x498/573mm).
• Broad side - Catalogue no. high 340995 ( 2 units of
103x573)
• Remove the front (see relevant section on: Service).
• Attach the panels (A) with countersunk head screws
through the 2 slits at the sides of the combustion
chamber. Make sure that the panels are parallel, ie:
equally far from the side borders and level with the
ends of the front panel narrow top, if that has been
installed.
• Put the front in place.
• Narrow top - Catalogue no. 340998 - (703x103mm)
• Broad top - Catalogue no. 340997 ( 838x103mm)
• Screw the two clasps (C) to the panel with M6x10mm
screws.
28
All manuals and user guides at all-guides.com
• Place the panel so that it lies on the inside of the front

Ash compartment

cat. no. 340732 (fig. 22)
• Remove the air distributor (A) and the internal screw in
• Lay a gasket (B) (enclosed in the box) along the edge of
• Lower the ash pail mantle (C) down through the bottom
• Lock the ash pail mantle with 4 plate screws from the
• Fasten the heat shield to the floor (fig. 4-A) under the
• Put the ash compartment (D) into position in the mantle.
• Lay the fire grate (E) in place in the combustion
• Lay the air distributor (A) in place so that it covers the
Fire screen (Jøtul I 80 Mini/Maxi -
Classic and Harmony)
When the fireplace is being used with the doors open,
always use a fire screen. It can be put in place with two
claws at the bottom end and a spring clip which is pressed
into the opening of the door at the top.
Grill - cat. no. 340957
If you would like to use the grill, this can be done by opening
the doors and placing the grill grid into the grooves in the
burning plates.
frame. Tighten the clasps with M6x20mm screws ans
nuts on the brackets for insert's heat shield.
the middle of the bottom of the combustion chamber
so that the fire plate and the cross bar can be removed.
the hole.
of the combustion chamber.
inside.
bottom of the ash pail mantle with M6x10mm screws
and nuts.
NB! The side which does not have a lip is placed against
the back wall.
chamber.
row of holes in the back burn plate.

Publicidad

Tabla de contenido
loading

Tabla de contenido