Troubleshooting; Technical Data - Cramer 2101786 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 19
EN
7

TROUBLESHOOTING

Problem
Possible Cause
The ma-
No electrical con-
chine does
tact between the
not start
machine and the
when you
battery pack.
push the
trigger.
The battery pack is
depleted.
The lock-out but-
ton and trigger are
not pushed at the
same time.
The ma-
The guard is not
chine stops
attached to the ma-
when you
chine.
cut.
Heavy cutting line
is used.
The grass winds
around the motor
shaft or the trim-
mer head.
The motor is over-
loaded.
The battery pack
or machine is too
hot.
The battery pack is
disconnected from
the tool.
The battery pack is
depleted.
English
Solution
1. Remove battery pack.
2. Check contact and in-
stall the battery pack
again.
Charge the battery pack.
1. Pull the lock-out but-
ton and hold it.
2. Pull the trigger to start
the machine.
Remove the battery pack
and attach the guard to
the machine.
Use only with the nylon
cutting line of 2.0 mm di-
ameter.
1. Stop the machine.
2. Remove the battery
pack.
3. Remove the grass from
the motor shaft and trim-
mer head.
1. Remove the trimmer
head from the grass.
2. The motor will recover
to work as soon as the
load is removed.
3. When you cut, move
the trimmer head in and
out of the grass to be cut
and remove no more than
8" in pass.
1. Cool the battery pack
until its function returns
to normal.
2. Cool the machine for
approximately 10 mi-
nutes.
Install the battery pack
again.
Charge the battery pack.
Problem
Possible Cause
The line
Lines are welded
does not ad-
to themselves.
vance.
Not enough line
on spool.
Lines are worn too
short.
Lines are tangled
on spool.
The line
The machine is
keeps
used incorrectly.
breaking.
The grass
Cut tall grass at
winds
ground level.
around the
trimmer
head and
motor hous-
ing.
The line
The cut-off blade
does not cut
becomes dull.
well.
Vibration
The line is worn
increases
down at one side
obviously.
and not advanced
in time.
8

TECHNICAL DATA

Voltage
48 V
No load speed
6000±10%/5000±10%min
trimmer),6300 ±10%min
ter)
Cutting head
Bump feed / Brush cutter blade
Cutting line diame-
2.0 mm
ter
Cutting path diam-
356 / 406 mm (Grass trimmer),
eter
254mm (Brush cutter)
Weight (without
3.5 kg
battery pack)
Battery model
BAM701/BAM710/BAM711 and oth-
er BAM series
Charger model
CAM805/CAM806 and other CAM
series
8
Solution
Lubricate with silicone
spray.
Install more line.
Advance the cutting line.
1. Remove the lines from
the spool.
2. Wind the lines.
1. Cut with the tip of the
line, avoid stones, walls
and other hard objects.
2. Advance the cutting
line regularly to keep full
cutting width.
1. Cut tall grass from the
top down.
2. Remove no more than
8" in each pass to prevent
wrapping.
Sharpen the cut-off blade
with a file or replace it.
Make sure that the line on
both sides is normal. Ad-
vance the line.
-1
(Grass
-1
(Brush cut-

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

48tx10

Tabla de contenido