Publicidad
Idiomas disponibles
Idiomas disponibles
6. When the tension in the wood fibres are released the
spring loaded limb may strike the operator and/or throw
the tool out of control.
7. Remove the tool from the cut while it is running at
full speed.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
•
Regularly remove the chain access cover and remove any
debris that has become trapped.
•
Regularly clean the ventilation slots with a clean, dry
paint brush.
•
To clean the tool, use only mild soap and a damp
cloth. Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.
Oiling (Fig. A, K)
Regularly oil the oiling points as indicated in Figure K.
Transporting
Always transport the tool with the jaws closed and the latch
in the locked position.
Saw Chain Sharpening (Fig. M, N, O)
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to
do this could result in serious personal injury.
WARNING: Sharp chain. Always wear protective
gloves when installing or removing the chain. The
chain is sharp and can cut you when it is not running.
To get the best possible performance from your chainsaw it is
important to keep the teeth of the chain sharp. Follow these
helpful tips for proper saw chain sharpening:
1. Remove the saw chain and use a chain vise when doing
any sharpening. See Removing the Saw Chain and
Chain Bar.
2. For best results use a 4.5 mm file and a file holder or filing
guide to sharpen your chain. This will ensure you always
get the correct sharpening angles.
3. Place the file holder flat on the top plate and depth
gauge of the cutter.
4. Keep the correct top plate filing angle line of 30 ° on your
file guide parallel with your chain (file at 60 ° from chain
viewed from above).
5. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your
saw chain around and repeat the processes (2, 3, 4) for
cutters on the other side of the chain. Use a flat file to file
the tops of the rakers (portion of chain link in front of the
cutter) so that they are about .025" (6.3 micrometers).
below the tips of the cutters.
6. Keep all cutter lengths equal.
7. If damage is present on the chrome surface of the
top plates or side plates, file back until such damage
is removed.
CAUTION: After filing, the cutter will be sharp, use
extra caution during this process.
nOTE: Each time the chain is sharpened, it loses some of the
low kickback qualities and extra caution should be used. It
is recommended that a chain be sharpened no more than
four times.
Storage
When the tool will not be used for several months, wipe any
metal components with oil.
Store the tool in a secure and dry location. The storage
temperature must always remain in the range of 41 °F (+5 °C)
to 104 °F (+40 °C). Place the product on a level safe location.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call 1‑888‑331‑4569 .
Versatrack™ (Fig. P)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: To reduce the risk of serious personal injury,
do not use a damaged Versatrack™ integral hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
integral hang hook or Versatrack™ Trackwall will not
support the weight of the tool.
English
13
Publicidad
