Publicidad
Idiomas disponibles
Idiomas disponibles
English
2. Rotate the two retention bolts
wrench
11
provided and remove completely.
3. Remove the chain access cover
4. Open the handles and pull back the top chain
cover jaw
1
.
5. Insert the chain guide bar
pulling the groove back.
6. Place the saw chain
13
around the front of the chain bar
and engage in the nose sprocket of the chain bar. Make
sure chain is installed properly, with the cutting teeth
facing forward.
7. Pull the chain bar and chain back, engaging it in the
groove in the chain bar and then over the sprocket
positioning teeth in the correct position on the sprocket.
8. Replace the chain access cover
bolts
10
tightening securely.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. I)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
6
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
16
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Usage (Fig. A, D)
1. Carry out regular cleaning of the unit as described in the
Maintenance section and in particular cleaning inside
the chain access cover.
2. The lower guard jaw
2
and top chain cover jaw
designed to close when one of the handles is released
or when the piece of branch being cut has been cut.
If this does not occur, discontinue use of the tool and
remove the battery pack. Check if any debris is blocking
movement. To help in this process it may be necessary
to remove chain access cover
problem is still present take the unit to a service center.
Proper Hand Position (Fig. J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
12
10
counterclockwise with
12
.
3
into the groove
14
by
15
12
and retention
into the tool handle, align the
1
are
12
. If on assembly the
A chain saw is intended for two‑handed use. Serious injury
to the operator, helpers, and/or bystanders can result from
one‑handed operation.
Oiling (Fig. A, K)
WARNING: A high quality bar and chain oil or SAE30
weight motor oil should be used for chain and bar
lubrication. The use of a vegetable based bar and
chain oil is recommended when pruning trees. Never
use waste oil or very thick oil. These may damage your
chain saw.
1. Before first use and every ten minutes of use you must
oil the product with the recommended chain oil. Open
the oiling cover
4
and insert the bottle into the oil
filling hole
17
apply pressure to the bottle once to
dispense oil.
2. This should be adequate for about 10 minutes of cutting
depending upon cutting speed and type of wood.
3. The hole feeds the oil through to the chain onto the
chain bar and an excessive amount of oil applied to
the unit could mean the oil drips from the unit around
the jaw area. This is normal and is nothing to be
concerned about.
Switching On and Off (Fig. A, L)
To open the handles, slide the latch
the handles apart. Ensure a firm grip on the handles and
then squeeze both on/off switch actuators
unit on.
For your safety, this tool is equipped with a double switching
system. This system prevents starting the tool inadvertently.
nOTE: Both switches must be activated for the product to
be used.
Do not force the tool ‑ allow it to do the work. It will do a
better and safer job at the speed for which it is designed.
Excessive force will stretch the chain.
Clearing a Jammed Saw Chain or Bar (Fig. A)
1. Switch the tool off.
2. Remove the battery from the tool.
3. Open the cut with wedges to relieve the strain on the
guide bar. Do not try to wrench the saw free. Start a fresh
cut. After use, close the handles and slide the latch
forward to the lock position. The handles should be
locked during transportation and storage.
Trimming Branches
1. Make sure the tool is running at full speed before making
a cut.
2. Hold the tool firmly in place to avoid possible bouncing
or sideways movement of the tool.
3. Guide the tool using light pressure.
4. Always cut down from the top. This way you will avoid
pinching the saw chain.
5. Remove branches. Starting from branch tip reduce
the branch in logical steps cutting off small sections.
When cutting a limb that is under tension be aware of
spring back.
5
backwards and pull
7
to switch the
5
Publicidad
