Publicidad
Idiomas disponibles
Idiomas disponibles
Course of X- and Y-Axis
The course of the X- and Y-axis is marked on
the housing above the rotation head.
Rotational Operation (RL25H)
The measuring tool exclusively operates with
a fixed rotational speed in rotational operation,
which is also suitable for use of a laser detector.
Overview (RL25HV)
All three operating modes are possible with
the measuring tool in horizontal and vertical
position.
Rotational Operation
R o t a t i o n a l
e s p e c i a l l y
when using the laser detector.
You can select between different
rotational speeds. 600 is optimal
for use with detector.
Line Operation (Sweep/
Scanning Mode)
In this operation mode, the
variable laser beam moves
within a limited aperture angle.
This increases the visibility of
the laser beam in comparison
to rotational operation. You can
select between different aperture
angles.
Point Operation (Spot mode)
This operation mode enables
the best visibility of the variable
laser beam. As an example, it is
used for easy projecting of heights or checking
building lines.
Rotational Operation, Point Operation
(RL25HV) (600/300/150/0 RPM)
Each time after switching on, the measuring
tool is in rotational operation with the highest
rotational speed. To switch from line operation
to rotational operation, press the rotational
operation button 4. Rotational operation starts
with the highest rotational speed. To change
the rotational speed, press the rotational
operation button 4 again. The rotational speed is
decreased each time after pressing the button.
After the lowest rotational speed, the measuring
tool switches to point operation. Pressing button
4 takes you back again to rotational operation
with the highest rotational speed. When working
with the laser detector, the highest rotational
speed should be set. When working without
laser receiver, reduce the rotational speed for
improved visibility of the laser beam and use the
laser viewing glasses 25.
All manuals and user guides at all-guides.com
Operation Modes
To switch to line operation, press the line
operation button 5. The measuring tool starts
with the smallest aperture angle. To change the
aperture angle, press the line operation button
5. The aperture angle is increased in two steps;
Pressing button 5 again takes you back to line
operation with the smallest aperture angle.
Note: Due to inertia, it is possible for the laser
to slightly move beyond the end point of the
laser line.
Rotating the Laser Point/Laser Line in the
Rotational Plane (RL25HV)
When automatic leveling is switched on
(indicator 11 is lit), the laser point or laser line
o p e r a t i o n
i s
can be rotated by 360° in steps within the
r e c o m m e n d e d
rotational plane, no matter if the measuring tool
is in horizontal or vertical position. To rotate the
rotational plane in clockwise direction, press
button 10; to rotate counter clockwise, press
button 9. Pressing and holding the buttons
increases the speed of the rotation head in the
desired direction (See Fig. G).
Aligning the Rotational Plane in the
Vertical Position (RL25HV)
When the measuring tool is in the vertical
position, it is possible to rotate the laser point,
laser line or rotational plane around the X-axis
for easy layout or parallel alignment. For this,
press the button for single-axis slope operation
12; indicator 11 flashes. Then, press button
10 to rotate the rotational plane in clockwise
direction, and button 9 to rotate in counter
clockwise direction. Pressing and holding the
buttons increases the speed of the rotation
head in the desired direction. Rotation is
possible within a range of ±8 % (See Fig. H).
Automatic Leveling RL25H
After switching on, the measuring tool checks
the horizontal position and automatically
compensates irregularities within the self-
leveling range of approx. 8 % (±5°). When the
measuring tool is inclined by more than 8 %
after switching on or after a position change,
leveling is no longer possible. In this case, the
rotor is stopped, the laser flashes, indicators
3 and 11 flash green. In this case, switch the
measuring tool off, re-align it and switch the
measuring tool on again. Without repositioning,
the laser is automatically switched off after 30
Min.
-14-
Line Operation (RL25HV) (10°/25°/50°)
Publicidad
