Descargar Imprimir esta página

Disposal; Declaration Of Incorporation - tormatic TAR1 Manual De Instrucciones Y De Montaje

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 36
11

Disposal

Dispose of packaging material in an environmentally friendly way
and in accordance with the applicable local disposal regulations.
The symbol with the crossed-out waste bin on waste elec-
trical or electronic equipment stipulates that this equipment must
not be disposed of with the household waste at the end of its life.
You will find collection points for free return of waste electrical
and electronic equipment in your vicinity. The addresses can be
obtained from your municipality or local administration. The sep-
arate collection of waste electrical and electronic equipment aims
to enable the re-use, recycling and other forms of recovery of
waste equipment as well as to prevent negative effects for the en-
vironment and human health caused by the disposal of hazard-
ous substances potentially contained in the equipment.
12

Declaration of incorporation

Declaration of Incorporation in accordance with the
EC Machinery Directive 2006/42/EC
Manufacturer's declaration of incorporation
(translation of the original)
For the installation of partly completed machinery in terms of the
EC Machinery Directive 2006/42/EC, Annex II Part 1 Section B
We hereby declare that the following partly completed machinery
– as far as possible with respect to the scope of supply –
complies with the essential requirements of the EC Machinery
Directive. The partly completed machinery is only intended to be
incorporated into a loading bridge to thus form a complete
machine within the meaning of the EC Machinery Directive. The
loading bridge must not be put into service until the final
machinery has been declared in conformity with the provisions of
the EC Machinery Directive and the EC Declaration of
Conformity according to Annex II A is available. We furthermore
declare that the relevant technical documentation for this partly
completed machinery has been compiled in accordance with
Annex VII, Part B, and undertake to transmit it through our
Documentation Department in response to a reasoned request
by the competent national authorities.
The EC type-examination procedure described in Annex IX was
performed by the approved testing laboratory
TÜVNORDCERT GmbH (NB 0044), Langemarckstr. 20,
45141 Essen. EC type examination certificate 44 780 13108303
Product model / product:
Product type:
Year of manufacture from:
Relevant EC/EU directives:
Directive 2014/30/EU
Directive 2011/65/EU
Fulfilled requirements of the EC Machinery Directive 2006/42/
EC, Annex I, Part 1:
1.2.1 Safety and reliability of controls:
Safety circuit STOP A PL c, Kat. 2, PFH = 5.9E-8
1.2.2 (partly), 1.2.3, 1.2.4, 1.2.6, 1.3.4, 1.5.1, 1.5.2, 1.5.3,
1.5.5, 1.5.6, 1.5.8, 1.5.9, 1.5.10, 1.5.11, 1.5.13, 1.5.15,
1.6.2, 1.6.3, 1.6.4,1.7
TAR1 400V / 230V
Loading bridge control
01/2020
Applied harmonised standards:
EN ISO 12100:2010-11
EN ISO 13849-2:2012
EN 1398:2009
EN 60204-1:2006-06
EN 60204-1:2006/AC:2010
EN 60204-1:2006/A1:200
EN 60529:1991-10
EN 60529:1991/AC:1993
EN 60335-1:2012/A13:2017
EN 61000-6-4:2007-01
EN 61000-6-4:2007/A1:2011
EN 61000-6-2:2005-08
Other applied technical standards and specifications:
EN 60335-1:2012 (as applicable)
EN 61000-6-3:2007 / A1:2011
EN 61000-6-2:2005 / AC:2005
The product must only be commissioned if compliance of the
loading bridge with the regulations of the Machinery Directive has
been ascertained.
Manufacturer and name of the authorised representative of
the technical documentation:
Novoferm tormatic GmbH
Eisenhüttenweg 6
44145 Dortmund
Place and date of issue:
Dortmund,
15.01.2020
Dirk Gößling, Managing Director
TAR1 400V / 230V
EN - 21

Publicidad

loading