Publicidad
Warm Saturator
This is a variety of saturator, and is distinctive for its warmer sound.
Parameter
20–16000 [Hz]
EQ Low Frequency
EQ Low Gain
-24–+24 [dB]
THRU, -12dB, -24dB
EQ High Slope
20–16000 [Hz]
EQ High Frequency
THRU, LPF, HPF, LSV, HSV Types of filter that precedes the distortion processing
DrvPre Type
DrvPre Frequency
20–16000 [Hz]
DrvPre Gain
-24.0–+24.0 [dB]
Drive
0.0–+48.0 [dB]
DrvPost1 Type
THRU, LPF, HPF, LSV, HSV Type of filter 1 which follows the distortion processing
DrvPost1
20–16000 [Hz]
Frequency
DrvPost1 Gain
-24.0–+24.0 [dB]
DrvPost2 Type
THRU, LPF, HPF, LSV, HSV Type of filter 2 which follows the distortion processing
DrvPost2
20–16000 [Hz]
Frequency
DrvPost2 Gain
-24.0–+24.0 [dB]
THRU, LPF, HPF, BPF,
PKG
DrvPost3 Type
DrvPost3
20–16000 [Hz]
Frequency
DrvPost3 Gain
-24.0–+24.0 [dB]
DrvPost3 Q
0.5–16.0
-60.0–0.0 [dB]
Makeup Sense
DrvPost Gain
-48.0–+12.0 [dB]
Drive Balance (*1)
D100:0W–D0:100W
Level
0–127
*1: This parameter corresponds to MFX Ctrl. For details, refer to
Ctrl)(P.203)".
*1: This parameter corresponds to MASTER EFFECT CTRL. For details, refer to
EFFECT (MASTER EFFECT
CTRL)(P.204)".
Value
Input filter (low range)
Boosts/cuts the sound below the specified frequency.
Amount of boost/cut
Input filter (high range)
Amount of attenuation per octave
THRU: No attenuation
-12 dB: gentle
-24 dB: steep
Input filter (high range)
Attenuates frequencies that are higher than the specified frequency.
THRU: No filter is applied
LPF: A filter that passes the sound below the specified frequency
HPF: A filter that passes the sound above the specified frequency
LSV: A filter that boosts/cuts the sound below the specified frequency
HSV: A filter that boosts/cuts the sound above the specified frequency
Frequency at which the pre-distortion filter operates
For the LSV/HSV types, the amount of boost/cut
Strength of distortion
Frequency at which post-distortion filter 1 operates
For the LSV/HSV types, the amount of boost/cut
Frequency at which post-distortion filter 2 operates
For the LSV/HSV types, the amount of boost/cut
Type of filter 3 which follows the distortion processing
THRU: No filter is applied
LPF: A filter that passes the sound below the specified frequency
HPF: A filter that passes the sound above the specified frequency
BPF: A filter that passes only the specified frequency
PKG: A filter that boosts/cuts the specified frequency
Frequency at which post-distortion filter 3 operates
For the PKG type, the amount of boost/cut
Width of the frequency range affected by the filter
Adjust this value so that the sound is not made louder when distortion is
applied.
Gain following distortion processing
Volume balance between the dry sound (D) and effect sound (W)
Output Level
Explanation
"Control del MFX con los mandos PAD EDIT [1] [2] (MFX
"Control del MASTER EFFECT con el mando MASTER
Effect List (English)
191
Publicidad
