Publicidad
Idiomas disponibles
Idiomas disponibles
4.
Short press the EMG key (6) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (8) to validate and exit the MENU.
disappears from the display.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
from the display.
Default COLOR is:
(orange).
2) DIMMER
DIMMER function allows adjusting the brightness of the lighting. 10 steps
from 0 to 9.
Press F key (8).
is displayed.
Long press F key (8) to enter the MENU.
1.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to select the
menu.
2.
Press EMG key (6) to validate. The current value blinks on the display.
3.
Turn the rotary CH knob (4) or use the UP/DN buttons (13) on the microphone
to change the value of the dimmer.
4.
Short press the EMG key (6) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (8) to validate and exit the MENU.
disappears from the display.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
from the display.
Dimmer default value is : 5.
3) TONE
This function allows to change the
Press F key (8).
is displayed.
Long press F key (8) to enter the MENU.
1.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to select the
menu.
2.
Press EMG key (6) to validate. The current value blinks on the display.
3.
Turn the rotary CH knob (4) or use the UP/DN buttons (13) on the microphone
to change the value of the tone.
4.
Short press the EMG key (6) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (8) to validate and exit the MENU.
disappears from the display.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
from the display.
Tone default value is : 0
disappears
disappears
RX
TONE. 11 steps from -5 to +5
disappears
4) KEY BEEP
When the function is activated, a beep sounds when a key is pressed, by
changing the channel etc. "BP" appears on the display when the function
is active.
Press F key (8).
is displayed.
Long press F key (8) to enter the MENU.
1.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to select the
menu.
2.
Press EMG key (6) to validate. The current value blinks on the display.
3.
Turn the rotary CH knob (4) or use the UP/DN buttons (13) on the microphone
to activate ( on) / deactivate ( of) the function.
4.
Short press the EMG key (6) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (8) to validate and exit the MENU.
disappears from the display.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
from the display.
Default KEY BEEP is On.
5) ROGER BEEP
When the function is active, the icon
The Roger Beep sounds when the PTT switch (12) on the microphone is re-
leased in order to let your correspondent speak. Historically as transceiver
is a "simplex" communication mode, it is not possible to speak and to listen
at the same time (as it is the case with a telephone). Once someone had
finished talking, he said "Roger" in order to prevent his correspondent that
it was his turn to talk. The word "Roger" has been replaced by a significant
beep. There comes "Roger beep" from.
Press F key (8).
is displayed.
Long press F key (8) to enter the MENU.
1.
Turn the rotary CH knob (4) or use UP/DN buttons (13) on the microphone
to select the
menu.
2.
Press EMG key (6) to validate. The current value blinks on the display.
3.
Turn the rotary CH knob (4) or use the UP/DN buttons (13) on the microphone
to activate ( 1 to 6*) / deactivate (OF) the function.
4.
Short press the EMG key (6) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (8) to validate and exit the MENU.
disappears from the display.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
from the display.
*6 roger tones for ROGER BEEP.
Default ROGER BEEP is OF.
12
disappears
appears on the display.
disappears
Publicidad
