Skil 0630 Manual Original página 14

the cutting blades against excessive wear
APPLICATION ADVICE
• For trimming a hedge at a uniform height level
- fasten a piece of string along the length of the hedge at
the desired height
- trim the hedge just above this string
MAINTENANCE / SERVICE
This tool is not intended for professional use
•
! always switch off the tool and remove the battery
• Keep tool and cutting blades clean
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- after use, always carefully clean and lightly lubricate the
cutting blades
! wear gloves when handling or cleaning the cutting
blades
• Regularly check the condition of the cutting blades and
the tightness of the blade bolts
• Regularly check for worn or damaged components and
have them repaired/replaced when necessary
• Sharpening the cutting blades
- remove cutting blades from tool before sharpening
- sharpen the cutting blades with a small and smooth file,
in case a solid object damaged them
- we advise you, however, to have the blades sharpened
by a specialist
- lubricate the cutting blades after sharpening
• Storage i
- store the tool indoors in a dry and locked-up place, out
of reach of children
- securely mount storage rail on the wall with 2 screws
(not supplied) and horizontally leveled
- use blade covers B (2) when storing the tool
- lubricate the cutting blades before storing the tool
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
TROUBLESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
Tool operates intermittently

- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service station
Motor runs but blades remain stationary

- internal fault -> contact dealer/service station
Cutting blades hot

- cutting blades blunt -> have blades sharpened
- cutting blades have dents -> have blades inspected
- too much friction due to lack of lubricant -> lubricate
blades
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
! remove the battery before disposal of the tool
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 73 dB(A) (uncertainty
K = 3.0 dB) and the sound power level 82.7 dB(A)
(uncertainty K = 2.8 dB), and the vibration <2.5 m/s²
(triax vector sum; uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
b
Cisailles à gazon/
à arbuste sans fil
INTRODUCTION
• Cet outil a été conçu pour tailler l'herbe, les buissons
et les haies ; il est uniquement destiné à un usage
domestique
• Cet outil n'est pas conçu pour un usage professionnel
Lisez attentivement ce manuel d'instruction avant
•
d'utiliser l'appareil et conservez-le pour pouvoir vous y
référer ultérieurement 3
• Prêtez particulièrement attention aux consignes de
sécurité et aux avertissements ; sinon, vous risquez
de subir des blessures graves
• Vérifiez que toutes les pièces montrées sur le schéma
sont contenues dans l'emballage 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
CARACTÉRISTIQUES TECHNIQUES 1
PIÈCES DE L'OUTIL 2
14
0630