Publicidad
Idiomas disponibles
Idiomas disponibles
3. Place small filter end of detergent siphoning tube into
detergent container.
NOTE: Make sure the filter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting filter into a detergent solution bottle, route tube
so as to keep it from inadvertently contacting hot muffler.
4. Make sure garden hose is connected to water inlet.
Check that high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE
You must attach all hoses before you start the engine.
• Starting the engine without all the hoses connected and without
the water turned ON will damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Start engine following instructions How to Start Your
Pressure Washer.
6. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
7. Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
IMPORTANT: You must flush the detergent siphoning system
after each use by placing the filter into a bucket of clean
water, then run the pressure washer with black detergent
nozzle for 1-2 minutes.
Pressure Washer Rinsing
1. Remove black detergent nozzle from nozzle extension.
2. Select and install desired high pressure spray tip
following instructions How to Use Spray Tips.
3. Keep spray gun a safe distance from area you plan to
spray.
WARNING
Kickback from spray gun can cause you to fall.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
All manuals and user guides at all-guides.com
4. Increase (decrease) spray pressure by turning pressure
5. Apply a high pressure spray to a small area and then
6. Start at top of area to be rinsed, working down with
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.
1. Remove high pressure spray tip from nozzle extension.
2. Select and install black detergent nozzle.
3. Place detergent siphoning tube/filter in a bucket full of
4. Flush for 1-2 minutes.
5. Shut off engine following instructions How to Stop
6. ALWAYS point spray gun in a safe direction, press red
IMPORTANT: Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
• Keep high pressure hose connected to pump and spray gun
• ALWAYS point spray gun in safe direction, press red button
Automatic Cool Down System
(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
the warm water onto the ground.
13
control knob (A) clockwise (counterclockwise). Use
lower pressure to wash items such as a car or boat. Use
higher pressure to strip paint and degrease driveways.
A
check the surface for damage. If no damage is found,
you can assume it is okay to continue rinsing.
same overlapping strokes as you used for cleaning.
clean water.
Pressure Washer and turn off water supply.
button and squeeze spray gun trigger to release retained
high water pressure.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
while system is pressurized.
and squeeze spray gun trigger, to release high pressure, every
time you stop engine.
Publicidad
