Publicidad
Idiomas disponibles
Idiomas disponibles
3.2
ACCESS TO INSTALLER'S
PARAMETERS
For access to the installer's parameters,
press simultaneously the keys of boiler
panel (
and
) for 5 seconds.
The red LED flashes and the display shows:
The parameters can be scrolled with
or
. To enter the parameter press
. The value set flashes, the display
shows:
Proceed as follows to change the set value:
– set the new value using
– confirm the set value using
Press
to exit the parameters section.
The display is shown automatically after 5
minutes. The parameters section contains
the alarms log, info and meters (display
only).
3.2. 1
Replacing the board or
RESETTING parameters
If the electronic board is replaced or reset,
it is necessary to configure PAR 01 and
PAR 02 by associating the following values
to each type of boiler to be able to restart
the boiler:
GAS
MODEL
-
METHANE
25/15
(G20)
-
-
-
PROPANE
25/15
(G31)
-
-
-
-
-
-
-
BOILER
-
-
-
with high powered mini reservoirs
NOTE:
The boiler panel has a label with the
values that have to be set for PAR 01 and
PAR 02 (fig. 19).
96
FAST CONFIGURATION
PAR DESCRIPTION
01 Combustion configuration
02 Hydraulic configuration
03 Disabling of voltage presence LED
04 Correction of external probe values
05 Timer block of the keys
09 Fan rpm Step ignition
or
D.H.W. - HEATING
PAR DESCRIPTION
10
Boiler antifreeze
11
External sensor antifreeze
12
Climatic curve setting
13
Minimum temperature heating
14
Maximum temperature heating
15
Maximum power heating
16
Post-circulation time
17
Pump heating activation delay
or
.
18
Re-ignition delay
or
.
19
Flow meter modulation saturation band
29
Anti-legionella (only D.H.W. tank)
PARAMETERS RE-SET
PAR DESCRIPTION
49 * Reset default parameters
(PAR 01 - PAR 02 equal "---")
* If the current setting is difficult to understand or anomalous behaviour or if it is difficult to understand
the boiler, it is advised to restore the initial parameter values by setting PAR 49 = 1 and PAR 1 and
PAR 2 as specified in point 3.2.1.
ALARMS (visualization)
PAR DESCRIPTION
A0
Last code anomaly appearance
A1
Code anomaly previously appearance
A2
Code anomaly previously appearance
A3
Code anomaly previously appearance
A4
Code anomaly previously appearance
PAR 1
A5
Code anomaly previously appearance
A6
Code anomaly previously appearance
01
A7
Code anomaly previously appearance
02
A8
Code anomaly previously appearance
03
A9
Code anomaly previously appearance
04
INFO (visualization)
05
PAR DESCRIPTION
06
i0
External sensor temperature
07
i1
C.H. 1 sensor temperature
08
i2
C.H. 2 sensor temperature
i3
Fumes sensor temperature
-
i4
Auxiliary sensor AUX temperature
-
i5
Set of effective heating temperature
-
i6
Level ionization flame
20
i7
Number of fan revolutions
i8
Flow rate
PAR 2
COUNTERS (visualization)
PAR DESCRIPTION
-
-
c0
Number hours of operation of the burner
-
c1
Number of ignitions of the burner
13
c2
Number total of the anomalies
c3
Number approached the parameters installator
c4
Number approached the parameters OEM
PARAMETERS INSTALLER
D.H.W. flow meter
RANGE
UNIT OF
INC/DEC
MEASUREMENT
UNIT
-- = ND
=
=
1 ... 20
-- = ND
=
=
1 ... 14
0 = Disabled
=
=
1 = Enabled
-5 ... 05
°C
1
-- = Disabled
Min.
1
1 ... 99
00 .... 81
rpm x 100 0, 1 from 0, 1 to 19,9 00
1 from 20 to 81
RANGE
UNIT OF
INC/DEC
MEASUREMENT
UNIT
0 ... 10
°C
1
-- = Disabled
°C
1
- 9 ... 05
03 ... 40
=
1
20 ... PAR 14
°C
1
PAR 13 ... 80
°C
1
30 ... 99
%
1
0 ... 99
10 sec.
1
0 ... 99
10 sec.
1
0 ... 10
Min.
1
0 ... 99
%
1
O = Disabled
=
=
1 = Enabled
RANGE
UNIT OF
INC/DEC
MEASUREMENT
UNIT
-- , 1
=
=
RANGE
UNIT OF
INC/DEC
MEASUREMENT
UNIT
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
RANGE
UNIT OF
INC/DEC
MEASUREMENT
UNIT
-9 ... 99
°C
1
-9 ... 99
°C
1
-9 ... 99
°C
1
-9 ... 99
°C
1
-9 ... 99
°C
1
PAR 13 ... PAR 14
°C
1
00 ... 99
%
1
00 ... 99
100 rpm
1
00 ... 99
l/min
1
RANGE
UNIT OF
INC/DEC
MEASUREMENT
UNIT
00 ... 99
h x 100 0, 1 from 0,0 to 9,9 00
1 from 10 to 99
00 ... 99
x 1000
0, 1 from 0,0 to 9,9 00
1 from 10 to 99
00 ... 99
x 1
00 ... 99
x 1
00 ... 99
x 1
DEFAULT
SETTING
"--"
"--"
01
00
15
DEFAULT
SETTING
03
- 2
20
20
80
99
03
01
03
30
0
DEFAULT
SETTING
=
DEFAULT
SETTING
=
=
=
=
=
=
=
=
=
=
DEFAULT
SETTING
=
=
=
=
=
=
=
=
=
DEFAULT
SETTING
1
00
1
00
1
00
Publicidad
