Ega Master 55815 Manual De Instrucciones página 19

12. After the mainframe is firmly installed on the pipes, take away circular Lock Pin.
Caution: make sure all the circular Lock Screw tightened before continuing the installing process.
13. Adjust the fixed Swelling Block pointed to the position of 12 o'clock or close to 12'clock.
Tighten fixed bolt of Swelling Block to make it equivalent that the distance from the mainframe to the top
and the bottom of the pipes.
14. Adjust the fixed Swelling Block at the position of 6 o'clock, and tighten the bolt. The same
way as Step 13.
15. Adjust the fixed Swelling Block at the position of 3 o'clock, tighten the bolt. The same way as Step 13.
by here, the mainframe is almost at a proper position.
16. Use the provided square to adjust the right and angle of machine and extend diameter of pipes.
Caution: here, the machine still can move. If necessary, loosen the fixed bolt at position of 3 o'clock and 9
o'clock to adjust them again.
17. When the angle between machine and pipe becomes a right angle, tighten Swelling Block Screw, and
fix the mainframe on the pipes.
18. Center the machine
A. Rotate the Cut-off Tool Bit to the position of 12 o'clock by hand.
B. Lower Tool Bit to the position which is 2mm to the upper of external diameter.
C. Rotate Tool Bit to the position of 6 o'clock, adjust the fixed swelling block to the center.
C1. If the Tool Bit at the position of 6 o'clock is closer to that at position of 12 o'clock, loosen the fixed bolt
at the position of 12 o'clock, then tighten the bolt at the position of 6 o'clock. By doing this, it will make the
machine move away from ektexine of pipe at the position of 6 o'clock and close to 12 o'clock position.
19. Repeat the steps above if necessary.
20. Thereafter, adjust Tool Bit to make sure it can run normally and avoid damage.
A. The extending distance from Cutting Tool Bit to the bottom of Tool Post equals to wall thickness + 3mm.
B. the extending distance from Beveling Tool Bit to the bottom of Tool Post equals to wall thickness + 2mm.
Caution: Fix Tool Bit in this way to make sure that Cutting Tool Bit can go first through the
pipe, and then make the Beveling Tool Bit work effectively.
Caution: Make sure that Tool Bit touch the correct side or the pipe's cutting line, and then A.
21. Rotate Star wheel clockwise to make sure no clearance between Star wheel Screw Stem and crew cap.
B. Make any point of the Star wheel point to red line on the top of Tool Slide.
C. Adjust the other Tool Slide by the same way.
D. Press Feed Link and mess Feed Star wheel.
22. Install Driving Motor, loosen two 8mm screws on the back of Pinion Housing.
23. Adjust two bolt holes on the motor, position the flange on the motor by using the screw on the pinion
and push the flange to upper screw.
Caution: Drive Motor can be installed in different positions for operators' convenience.
24. Tighten two screws to fasten the motor.
25. Start up the machine and confirm the Tool Bit clearance.
A. Rotate Cutting Tool Slide Star wheel clockwise until it make the tool 2mm off the ektexine of pipes.
B. Connect electricity.
C. Switch on the engine, rotate around the ektexine of the pipe to check the
clearance.
D. Adjust to meet needs.
26. Start cutting process
At first, make the tool post rotate at a uniform speed to check if the Star wheel is properly timed. If the Star
wheel can't mesh the Feed Link smoothly, cut off the power and readjust by timing process of Star wheel
(Step 21, from A to C).
27. Adjust rotation speed of Tool post.
28. while machining, ensure plenty coolant for constant processing.
Caution: while cutting, make Tool Slide within the red line.
Caution: mind the falling pipes while cutting long work piece.
29. After complete cutting, loosen the motor trigger or switch off the electricity, and dismantle the process.
Caution: after machining, ensure the machine clean, no metal scraps, no coolant remains
for machine storage. Open the machine into halves and check if there is any remains in the slide way.
30. Pull out the Feed Link, Cutting and Beveling Tool Bit.
31. Loose fixed Swelling Block and insert the Lock Pin into the mainframe ring.
19