Publicidad
Idiomas disponibles
Idiomas disponibles
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly and
shorten the tool's service life
• Clean the body of your tool with a soft brush or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on
a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
To replace the brushes:
1. Remove the 2 x Brush Access Covers (12) (Fig. XXIV)
2. Carefully remove the worn brushes (Fig. XXIV) and ensure the sockets are clean
3. Carefully replace with 2 x new brushes (always replaced both brushes at once) then replace the
Brush Access Covers
4. After fitting, run the router without load for 2-3 minutes to help the brushes bed in
Note: The process of the brushes fully bedding in may take repeated uses. Motor sparking may
continue until new carbon brushes have bedded in.
• Alternatively, have the tool serviced at an authorised service centre
Troubleshooting
Problem
No function when ON/OFF Rocker Switch (11) is operated
Inaccurate cutting profile
Router will not operate
Router runs or cuts slowly
Excessive vibration
EN
Heavy sparking occurs inside motor housing
Micro Winder (21) "clicks" or not adjusting
Makes an unusual sound
14
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-GB/Support
Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in the case provided
• Store in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools
Possible Cause
No power
Defective ON/OFF Rocker Switch
Depth Stop (4) not correctly adjusted
Incorrectly fitted or loose router bit/Collet (5)
No supply of power
Brushes worn or sticking
Switch is faulty
Motor components faulty or short circuited
Blunt or damaged cutter
Speed Controller (14) set low
Motor is overloaded
Incorrectly fitted or loose router bit
Bent or damaged router bit
Brushes not moving freely
Damaged or worn motor
Plunge Lock Lever (16) engaged
Reached end of adjustment range
Mechanical obstruction
Damage to internal windings
EU Address:
Toolstream B.V.
De Keten
00004
5651 GJ
Netherlands
Solution
Check power supply
Replace the ON/OFF Rocker Switch at an authorised Triton service
centre
Ensure the Depth Stop corresponds to the maximum amount of cut
permitted by the Turret Stops (3)
Tighten router bit/Collet and cutter assembly
Check power is available at source
Disconnect power, open Brush Access Covers (12) and ensure
brushes are not damaged or heavily worn
Have the tool serviced by an authorised Triton service centre
Re-sharpen or replace cutter
Increase variable speed setting
Reduce pushing force on router
Refit or tighten router bit
Replace router bit
Disconnect power, remove brushes, clean or replace
Have the tool service by an authorised Triton service centre
Release Plunge Lock Lever
Reset the Micro Winder and set depth with the Depth Stop (4)
Have the tool serviced by an authorised Triton service centre
Publicidad
