KUNERT LAZZIO Manual De Instrucciones página 10

The pram also comes with a car seat option for children. To mount the car seat, the car seat adapters need
to be mounted first to the chassis. To mount the adapters on the chassis, click them into designated slots
one on each side of the pram
(
adapters are correctly mounted. Both adapters should be locked. After correct mounting of the car seat
adapters on the chassis, you can move on to mounting the car seat. To mount the car seat, you need to fit
its buckles into matching plastic handles on the adapters (fig. 24). This pram does not substitute a cradle or
a crib. If your child needs to sleep, it is recommended to put him/her in an appropriate carrycot, cradle or
crib. The car seat comes with a hood and a cover which are mounted with snaps. The car seat is equipped
with an adjustable handle. The handle is adjusted by pressing the red buttons on both sides of the car seat
and moving the handle into a desired position (fig. 25). To remove the car seat, you need to pull the levers
on both sides of the car seat (fig. 26). To dismantle the adapters, press the buttons on the both sides of the
pram chassis. Car seats of the Kunert model: Carlo and Kent are dedicated to this stroller model.
To adjust the handle height, you need to press the buttons on both sides of the handle and then adjust the
height while simultaneously pressing the buttons (fig. 27).
To mount the carrycot on the chassis, click it into designated slots (one on each side of the pram) (figs 10,
11) until the hooks are locked. The hooks are locked automatically. Warning The carrycot should always be
mounted rear-facing (so that the child faces the person pushing the pram). To take the carrycot off, press
the adapter buttons on both sides of the pram (fig. 11) and lift the carrycot up using the handle.
The carrycot has a permanently attached hood. You can adjust the hood as necessary by pressing buttons
on both sides of the hood and positioning the hood as necessary (fig. 12). The hood has a handle which is
used to carry the carrycot (fig. 13).
The carrycot is equipped with a cover which can be mounted by attaching the snaps of the cover to the
respective snaps on both sides of the hood (fig. 14). The cover has an anti-wind curtain with pentel
fasteners at the top of the booth.
MOUNTING AND REMOVAL OF THE PRAM SEAT
To mount the seat on the chassis, click it into designated slots (one on each side of the pram) (fig. 15) until
the hooks are locked (fig. 11). The hooks are locked automatically. The stroller seat may be mounted in
front-facing and rear-facing positions.
WARNING! Before you use the pram, make sure all blocking devices are activated.
To remove the seat, press the buttons on the both sides of the pram chassis (fig. 11).
WARNING This seat is not suitable for children under 6 months.
The pram seat is equipped with a protective hood. To mount it, slide its hooks into designated slots on
both sides of the pram seat chassis until the hood is locked (fig. 16).
To remove the hood, press the buttons of the hooks on both sides and pull up the hood (fig. 16). The
position of the hood is adjustable. It can be positioned differently. To adjust the hood position, move it
forwards or backwards to achieve the desired result (fig. 17). If a new born baby is put in the stroller, it is
recommended to set the position of the seat which is to be used from the baby's birth in a position similar
to a lying one.
The backrest can be adjusted in 4 positions. To lift the backrest up, you need to pull up the lever from
under the back of the seat and at the same time pull up the backrest up until you reach the desired
position. Next, release the lever (fig. 18). To recline the backrest, you need to pull up the metal lever, place
it in the desired position and release the lever.
The backrest can also be folded forward. To do this, lift the backrest up and then release the lever and pull
the lever up again while holding the backrest forward onto the seat. To restore the backrest to the stroller
version, raise the backrest to the vertical position and then lay it flat. (Fig 32).
The pram has front swivel wheels with a lock of the straight-ahead push. In order to lock the wheels, first
position them parallel to the rest of the pram and then turn the rim to the right (fig. 29). In order to unlock
the front wheels to go in all directions, simply turn the rim to the left.
FOLDING AND UNFOLDING THE PRAM CHASSIS
) (fig. 23). WARNING! Before using the car seat, ensure that the car seat
HANDLE HEIGHT ADJUSTMENT
MOUNTING AND REMOVAL OF THE CARRYCOT
CARRYCOT HOOD
CARRYCOT COVER
PRAM SEAT HOOD
BACKREST ADJUSTMENT
SWIVEL FRONT WHEELS
10