KUNERT LAZZIO Manual De Instrucciones página 11

To unfold the pram chassis, lay it down flat, push the lock (fig. 1) and pull it up strongly while holding the
handle until the locking mechanism will lock into place (fig. 2).
WARNING! Always slightly lift the handle of the trolley while pressing the buttons
WARNING! Before using the pram, ensure the locking mechanisms are activated, if not, pull them tighter.
The chassis may be folded in two ways (with and without wheels):
- to fold the chassis with the wheels, first lock the front wheels by positioning them across the to the
pram. Then pull the levers (fig. 3) on both sides of the handle (fig. 4).
- to fold the chassis without wheels, take off two front wheels (fig. 5) and rear wheels
(fig. 6). Then pull the levers (fig. 3) on both sides of the handle (fig. 4).
PARKING DEVICE
To activate the parking device, you need to step on the lever at the bottom of the pram (fig. 28). The
parking device will be released when the lever is lifted.
FOOTREST ADJUSTMENT
The footrest can be adjusted by simultaneously pressing side buttons while putting it in the desired
position (fig. 19).
MOUNTING AND REMOVAL OF REAR WHEELS
Before mounting the wheels, first mount the axes in the pram chassis. In order to mount the
axes, push the larger end of the axis into the absorber by pressing the red button, and then
release the button. Mount the axes on both sides of the pram and check whether fixed properly
(fig. 9).To mount the rear wheels, press the metal button in the central part of the wheel (fig. 6)
and then slide the wheel on the axis as far as it will go, release the button and pull back the
wheel until you hear a "click" sound.Always check whether the wheels are mounted correctly. In
case the pram wheel comes of when pulled, repeat the wheel mounting procedure until
mounted properly.
FASTENING THE HARNESS
In order to fasten the harness, click the ends of the harness in hooks on both sides of the carrycot. (The
harness is not provided with the pram).
GUIDELINES AND WARNINGS
- Before assembling the pram, ensure that all the components are fit to use. If they are damaged, the
product should not be used.
- When you fold and unfold the pram, ensure that the child is at a safe distance.
- The parking device must be used every time the pram is stopped.
- While adjusting the pram, you must ensure that no moving parts are directly touching the child.
- Any additional weight on the handle of the pram, the front/back of the seat and/or sides of the pram
makes it unstable.
- When going up a curb or any other step, it is important that you lift the front wheels.
- Store the pram in an area inaccessible to the child.
The pram must not be ridden down the stairs.
The pram should only be used with its original parts authorized by the manufacturer.
The chassis of the pram is compatible only with an original carrycot, seat and car seat provided by the
manufacturer. Only original components included in the set guarantee full compatibility and proper
functioning of the pram. Every Kunert pram is marked with the company logo for product identification
purposes. The upholstery of the pram may be cleaned with a soft cloth, using soap or other mild cleaning
agents. You can apply oil or grease to the pram's axes, thus protecting it from excessive wear. Any
additional seat should be equipped with a clear compatibility statement with a specific pram. Accessories
not accepted by the manufacturer should not be used. Only spare parts provided or recommended by the
manufacturer/distributor should be used. The parking device should be active when you put in and take
out children for the pram. The harness attaching hooks are located in the gondola. When mounting the
harness, fasten it to the hooks (handles) of the harness and check the correctness of the attachment.
The maximum wheel pressure is 0,8 BAR.
This product is suitable for a child who cannot sit up by itself, roll over and cannot push itself up on its
hands and knees. Maximum weight of the child: 9 kg
UNFOLDING OF THE LIE FLAT SEAT
Before attaching the lie flat seat to the frame of the pram it is necessary to unfold it. In order to
do that, lay it flat on the ground (canopy up) and take out the white mattress. At the bottom of
the lie flat seat there are two transverse wires. By lifting the lie flat seat with the canopy keep
11