Publicidad
Idiomas disponibles
Idiomas disponibles
1
Mark the general area where the mounting bracket will be located. Using a small drill or nail, make two small pilot holes at the marked
1
locations. Align the mounting brackets and drive screws into place. NOTE: Ensure mounting location of Function Controller is within 5ft
of an electrical outlet. Ensure mounting location of puck is within 24in of function controller.
2
Lift the fixture toward the mounting bracket. Apply upward pressure until channel snaps into place and seats into the bracket.
3
Connect fixtures, function controller, and plug-in driver by using the provided linking cords. Use strip to mount function controller. Use
provided cord clips where additional wire management is needed. Clean area, peel backing o the clips and mount where needed. Plug
the plug-in driver into the outlet.
CARE AND MAINTENANCE:
Periodically clean the fixture and di user using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned o . Do not
spray cleaner directly onto any part of the fixture or LEDs.
Good Earth Lighting
- 6 YEAR LIMITED WARRANTY:
®
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase
by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will
repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without
charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of
purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be
accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any
other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor
costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence,
strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may
also have other rights which vary from state to state.
FCC STATEMENT:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the
equipment and receiver. 3) Connect the equipment into an outlet on a circuit di erent from that of the receiver. 4) Consult the dealer or an experienced radio/TV
technician for help.
FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA
Telephone number: 1-800-291-8838
PROBLEM
1. Light does not come on.
2. Fuse blows or circuit breaker trips when
light is turned on.
REPLACEMENT PARTS LIST
Need Help?
Good Earth Lighting
1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
®
Good Earth Lighting
is a registered trademark of Good Earth Lighting, Inc.
®
© 2023 Good Earth Lighting, Inc. REV04.23
SCREW MOUNT INSTALLATION
2
DIMMING AND COLOR ADJUST
Tap button to turn On/O
Hold button down to Dim the
Fixture.
TROUBLESHOOTING GUIDE
POSSIBLE CAUSE
1. Power/ light switch is o .
2. Bad switch.
1. Discontinue use.
ZH-UC1357-F04
Hardware Kit:
Please visit our website at: https://goodearthlighting.com/contact-usor call the
Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
3
CORRECTIVE ACTION
1. Verify power supply and light switch are on.
2. Test or replace switch.
1. Call customer service (1-800-291-8838).
Manual Control: Short press COLOR
ADJUST button to select
3000K/4000K/5000K, Red, Green, Blue,
Pink, Orange, Auto rotating colors.
WIFI Control: See APP instruction sheet
for direction.
Printed in Vietnam
2
Publicidad
