Publicidad
Idiomas disponibles
Idiomas disponibles
Recommended Maintenance Schedule
5
To ensure safe riding, day to day care and regular maintenance are essential. You, the owner, have control and knowledge of
how often you use your scooter, how hard you use it and where you use it. It is the owner's responsibility to perform regular
checks and bring your scooter to authorized service center for inspection and service. Please refer to the maintenance
schedule below.
Note: This maintenance schedule charges a service fee.
Item
Component
Maintenance method
Mainframe parts
Use a soft, wet cloth to wipe the mainframe clean.
F25I: Inflate tires to 40–45 psi.
Tire pressure
F40I: Inflate tires to 50–55 psi.
Note: Remember to screw the valve cap after inflating!
Check if the tires are cracked, deformed, or
Tire wear
significantly worn.
Tighten the six screws fixed with the handlebar and the
stem. The suggested torque is 5.5±0.5 N·m.
Tighten the screw on the throttle. The suggested
Screws on the
Mainframe
torque is 3.5±0.1 N·m.
stem top
maintenance
Tighten the screws on the brake lever. The suggested
torque is 5.5±0.1 N·m.
Tighten the screws on the stem top. The suggested
torque is 10±0.5 N·m.
Tighten the two screws fixed with the front fork and the
folding mechanism. The suggested torque is 10±1 N·m.
Screws on the
If the stem gets shaky when riding, tighen the screw on
folding
the folding mechanism when the scooter is in folded
mechanism
state. The suggested torque is 12.5±1 N·m.
Brake disc
Tighten the screws on the brake disc assembly. The
assembly
suggested torque is 7.7±0.2 N·m.
09
Every 6
After 2 years or
months or
the total
Every 3
every 310
mileage > 3107
months
miles (500
miles (5000
km)
km)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Item
Component
Maintenance method
To accelerate and decelerate, check if the hub motor is stalled
Hub motor
or has abnormal sounds.
Rear wheel
Check if the rear wheel is stalled or gets shaky, or the axis shaft
is unbalanced.
maintenance
If the brake is too tight/loose, use the 4 mm Allen key to loosen
Brake
the screw on the caliper. Then slightly adjust the brake line
adjustment
(decrease/increase the exposed length), and tighten the
screw again.
Spin the wheels, the caliper should be aligned with the rotor and
Brake rotor
they shouldn't rub on the brake pads.
Taillight
Squeeze the brake lever, the tail light works normally.
Headlight
Check the headlight and see if it lights brightly.
Function
Inspection
Toggle the direction indicator button to the left/right
Direction
respectively, check if the direction indicators on the left/right
indicators
side flash normally.
Power on the scooter, the dashboard works properly.Switch
Dashboard
between the speed modes, the dashboard will display the
corresponding speed mode icon.
Bell
Ring the bell, the sound is loud.
Buzzer
Power on/off the scooter, the buzzer sound is normal.
Press and hold the throttle then release it, checking for
Throttle
acceleration and deceleration.
Note: Release it, check if the throttle will back to the position.
After connecting with the Segway-Ninebot app:
Fault
1) Update the firmware to the latest version.
detection
2) Check if the notification of the corresponding error code and
possible causes will prompt when the scooter detects an error.
Every 6
After 2 years or
months or
the total
Every 3
every 310
mileage > 3107
months
miles (500
miles (5000
km)
km)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
10
Publicidad
