cecotec MAMBO TOUCH Manual De Instrucciones página 28

ENGLISH
- Butterfly whisk
- 2-level steamer
- Spatula
- Instruction manual
- App manual
- Clean the jug and other accessories thoroughly with hot water, detergent, and a
non-abrasive sponge.
- Place the food processor on a flat, stable surface. Maintain a minimum distance of 110 mm
between the socket outlet and the wall, surrounding furniture, and your food processor.
- Use a damp cloth to clean the main body and wipe it dry.
Warning
Do not place the food processor on any surface that it is not heat-resistant.
3. OPERATION
Assembling the stainless-steel jug
- Place the jug in the main body, matching the mark on the jug with the front of the main
body if not correctly placed and try to start cooking. The display will show the warning A2.
Fig. 2
- There are capacity marks on the side of the jug. The jug's maximum usable capacity is 2.3
L when using the food processor at speed 0 and 1.8 L when using the food processor at a
speed between 1 and 10, or with one of the pre-set functions.
Assembling the hinged lid
- Place the lid on the jug matching the markings on the jug and the lid, press the lid around
the jug's rim and turn the lid clockwise to secure it. Should the lid not be correctly fitted
when the speed is not on 0, the A1 warning will appear on the display. Fig. 3
- When you open the lid, you can leave it in the folding position; just turn the lid
counterclockwise until it is fixed in the support. This way you can open the lid without
removing it completely. Fig. 4
Assembling the accessory and fixing bracket
- Make sure the accessory bracket's sealing gasket is properly installed. When installing it
on the jug you must take into account that the bracket must be placed a certain way. Make
sure it fits correctly. Fig. 5
- Hold and install the accessory bracket making sure it is correctly fitted and turn it
clockwise. Fig. 6
- Install the fixing bracket in the bottom part of the jar and turn it clockwise to fix the
accessory bracket to the jar. Fig. 7
54
Blade assembly
- Once the accessory bracket is installed and secured, place the blades in it and, pressing
down, rotate counterclockwise. Fig. 8 and make sure that they move slightly upwards
again, thus locking into their safety housing. It is very important to ensure they are properly
housed and secured. To make sure, once in place, pull them very gently and check that they
are not easily removable.
- To remove them, press and turn clockwise. The blades are very sharp. Use extreme caution
when handling them.
Warnings
- Use a cloth to cover the blades unit before handling them to avoid injuries.
- Assemble the fixing bracket and the sealing ring properly to avoid food or liquids being
cooked from splattering.
Tip
Setting speed 1 may be helpful when removing the blades until you are familiar with the
removal system.
Assembling the MamboMix spoon
Remove the blades and attach the MamboMix the same way you attached the blades. It
can be used for kneading or stirring and mixing without cutting the food. Do not use it for a
speed higher than 3, otherwise it will generate high vibration in the food processor and cause
hazards. Fig. 9
Warnings
It is possible for some food to get between the wall of the jug and the MamboMix spoon. If this
happens, the motor will stop operating as a safety method. Use the spatula to mix and remove
the stuck food for the food processor to resume the cooking process.
Assembling the measuring cup
- The measuring cup is used as a cover accessory to avoid splashing and reduce heat loss
during cooking. In addition, it is marked with a ml measurement scale
- To place it in the lid, make sure the clamping tabs fit correctly into the lid and turn clockwise.
Fig. 10
Warning
- Use the measuring cup and not any accessory or object to avoid splashing and reduce heat
loss of the jar.
- When cooking with temperature setting, place the measuring cup in the cover's gap
without locking it in place. This way, steam will be safely released.
ENGLISH
MAMBO TOUCH 55
MAMBO TOUCH CON JARRA HABANA