Descargar Imprimir esta página

Cybex Silver SOLUTION X I-FIX Guia Del Usuario página 10

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 33
PRODUCT PARTS
EN
(a) Backrest
(b) Reclining Headrest
(c) Headrest Height Adjuster
(d) Booster
(e) Lap Belt Guide
(f) Shoulder Belt Guide
INITIAL ASSEMBLY
Connect the backrest (a) to the booster (d) by hooking the guide lug on the
axis of the booster. The backrest (a) is then folded forward.
THE CORRECT POSITION IN THE VEHICLE
With retracted ISOFIX Locking arms (g) the car seat can be used on vehicle
seats which are equipped with an automatic three point belt. For using ISOFIX
please refer to the vehicle type list for approved vehicles. You can obtain
the most up-to-date version from
compatibility.
Above a child's stature of 135 cm, the compatibility between the Solution X
i-Fix and your vehicle might be reduced. Please review the vehicle type list
to check whether the car seat can be used in all headrest positions without
restrictions.
In exceptional cases, the car seat may also be used on the front passenger
seat. Always comply with the recommendations of the vehicle manufacturer.
INSTALLING THE CAR SEAT IN THE VEHICLE
1. Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the car seat on the front passenger seat, adjust the vehicle
seat as far back as possible without affecting the belt routing.
2. Use the ISOFIX adjustment handle (h) under the booster (d) and pull the
two ISOFIX locking arms (g) to their furthest extent.
3. Now twist the ISOFIX locking arms (g) 180° so that they are facing the
direction of the ISOFIX anchorage points (k).
4. Place the car seat on the appropriate seat in the vehicle.
5. Push the two ISOFIX locking arms (g) into the ISOFIX anchorage points (k)
until these lock into place with an audible "CLICK".
6
(g) ISOFIX Locking Arms
(h) ISOFIX Adjustment Handle
(i) ISOFIX Release Button
(j) ISOFIX Safety Indicator
(k) ISOFIX Anchorage Points
go.cybex-online.com/solution-x-ifix-car-
6. Use the ISOFIX adjustment handle (h) and push the car seat against the
vehicle seat.
7. Ensure that the entire surface of the backrest (a) of the car seat is placed
against the backrest of the vehicle seat.
�� If the headrest of the vehicle is in the way, pull it upwards to its furthest
extent or remove it completely (except in rear-facing vehicle seats).
8. Ensure the seat is secure by trying to pull it out of the ISOFIX anchorage
points (k). The green safety indicators (j) must be clearly visible on both
sides of the seat.
9. In case the seat is used without ISOFIX, it can be stored away on the bottom
of the seat.
�� By using ISOFIX, a connection to the vehicle is created which increases
your child's safety. Your child still needs to be secured with the three-point
belt of the vehicle.
REMOVING THE CAR SEAT FROM THE VEHICLE
Perform the installation steps in the reverse order.
1. Unlock the ISOFIX locking arms (g) on both sides by pushing the ISOFIX
release buttons (i) and pulling them back simultaneously.
2. Pull the seat away from the ISOFIX anchorage points (k).
3. Remove the car seat and store the ISOFIX System in reverse order to
installation.
RECLINING HEADREST
The Reclining Headrest (b) helps to prevent the child's head from dangerously
tipping forward during sleep. It can be set to one of 3 positions. Push the
Reclining Headrest (b) forward until the desired position is reached. To return
it to the original position, the reclining headrest (b) must be lifted and pulled
back.
�� The child's head should always be in contact with the Reclining Headrest.
ADJUSTING THE HEADREST
The headrest (b) can be adjusted by using the headrest height adjuster (c)
at the back of the headrest (b). There are 11 height positions that can be set.
Adjust the headrest (b) so that max. 2 cm (approx. 2 finger's width) remain
between the child's shoulder and the headrest (b).

Publicidad

loading

Este manual también es adecuado para:

522003967522003959522003961522003963