VONROC PD501AC Traducción Del Manual Original página 12

EN
Mounting the quick­action clamp (Fig. B, C, H)
Risk of injury! It is forbidden to hold
workpieces by hand as this is dangerous.
Always secure the workpiece in a machine
vice or a similar clamping device.
1. Follow the steps from the chapter "Assembling
the pillar to the base" but insert the quick-acti-
on clamp (9) to the pillar (23) before inserting it
into the baseplate (5), as shown on figure C2.
2. Ensure the notch inside the quick-action clamp
(9) is aligned to the side of the pillar (23) with
the protruding gear rack. A properly mounted
quick-action clamp (9) is shown on figure B.
3. Now insert the quick-clamping lever (10) into
the quick-action clamp (9) as shown on figure H.
Mounting the machine vice (Fig. A, I)
Risk of injury! It is forbidden to hold
workpieces by hand as this is dangerous.
Always secure the workpiece in a machine
vice or a similar clamping device.
The baseplate is provided with grooves for fixing
the clamping tools.
1. Start by loosely hand-tightening the bolts (15),
washers (13), spring washers (12) and nuts
(14) to the machine vice (11), as shown on
figure I.
2. Now slide the machine vice (11) into the grooves
of the baseplate (5) as shown on figure I.
3. Put the machine vice (11) in the desired positi-
on and tighten the nuts (14). A size 17 wrench
(not included in the supply) should be used.
4. The machine vice (11) jaws can be opened by
turning the lever anti-clockwise and closed by
turning it clockwise.
Mounting the parallel fence (Fig. J, K)
Risk of injury! It is forbidden to hold
workpieces by hand as this is dangerous. The
parallel fence can only be used in conjuncti-
on with the quick-action clamp or a similar
clamping device. It is not allowed to use the
fence and hold the workpiece by hand.
1. Start by loosely hand-tightening the knobs
(18) and square nuts (17) to the fence (16), as
shown on figure J.
2. Now slide the fence (16) into the grooves of the
baseplate (5) as shown on figure K.
12
3. Put the fence (16) in the desired position and
tighten the knobs (18) by hand.
4. The fence (16) position can easily be adjusted
by loosening the knobs (18) and tightening
them again afterwards.
Install of a stationary machine (Fig. A, B)
To ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use. You can install the machine in
two ways:
1. On a workbench
In this case the machine must be secured to the
workbench using suitable screw fasteners. Use the
four holes (24) in the baseplate (5) to do this. As
shown on fig. D.
2. On a subframe
Read all the warnings and instructions
included with the stand. Failure to observe
the warnings and follow instructions may
result in electric shock, fire and/ or serious
injury.
Assemble the stand properly before
mounting the power tool. Correct assembly is
important to prevent the risk of collapsing.
In this case the machine must be secured to the
sub frame with bolts. Use the four holes (24) in the
baseplate (5) to do this. The sub frame must be
anchored with 4 bolts to the floor plate with dimen-
sions of at least 1 square meter.
4. OPERATION
Always check the protective guards before
use.
Check the drill and its safety devices for
damage and impairments. Do not use the
drill if you discover any damage or impair-
ments and contact Vonroc customer service.
Ensure that the voltage of the mains supply
complies with the specifications on the
rating plate.
Connect the machine only to a socket with
the properly installed earthing contact.
WWW.VONROC.COM