Publicidad
Idiomas disponibles
Idiomas disponibles
EN
activate the drill by pressing the power button
(38).
2. Wait for a few seconds until the drill reaches its
current speed. You can observe the increasing
speed on the display (30), see also figure L2.
3. Press the "+" button (40) to increase the speed.
4. Press the "-" button (41) to decrease the speed.
Switching the laser / LED worklight on or off (Fig.
A, L)
• Ensure the display (30) is switched on by pres-
sing the (I) button on the On/Off switch (29) and
activate the drill by pressing the power button
(38).
• Press the laser / LED worklight button (42)
button repeatedly to switch between the Laser -
Light - Laser / Light modes.
• The respective mode setting is shown on the
display (30), see also figure L3.
-
"Laser" = Cross laser switched on
-
"Light" = LED work light is switched on
-
"Laser & Light" = Cross laser and LED work
light both switched on.
• To switch off, change the modes or press the
laser / LED worklight button (42) several times
until nothing is shown on the display.
Adjusting the laser (Fig. A, L)
Note: To test the laser function, the power tool
must be connected to the power supply.
While adjusting the laser (e.g. when moving
the tool arm), never activate the on/off
switch. Accidental starting of the power
tool can lead to injuries.
If the laser (20) ceases to indicate the correct cut-
ting line, you can readjust the laser. To do so:
1. Loosen the screw (44) and adjust the laser
position.
2. Tighten the screw (44).
Displaying the drilling depth or speed (fig. A, L)
By pressing the speed or depth selection button
(39), the drilling speed or the drilling depth can be
selected on the display (30).
• Ensure the display (30) is switched on by pressing
the (I) button on the On/Off switch (29) and acti-
vate the drill by pressing the power button (38).
• By default, the speed is shown on the display,
as shown on Fig. L2.
14
• Press the speed or depth selection button
(39) to change the display to drilling depth, as
shown on figure L4.
• Press the speed or depth selection button (39)
again to change back to the speed display, as
shown on figure L2.
Defining the drill depth zero point (fig. A, L)
1. Ensure the display (30) is switched on by pres-
sing the (I) button on the On/Off switch (29) and
activate the drill by pressing the power button
(38).
2. Change the display to the drilling depth (see
chapter "Displaying the drilling depth or
speed").
3. Move the machine head downwards when the
drill bit is rotating using the drill depth handle
(4). The display shows the deviation continuo-
usly from the current zero point.
4. Stop at the desired position and press the zero
point button (43) to define the current depth /
height as the new zero point.
5. The display shows the new starting point as
"0.0".
Height adjustment (Fig. A, B)
Do not adjust the height of the drive unit
during operation. Only operate clamping
lever (36) when the drill depth handle (4) is
in its initial position. This precautionary
measure prevents potential injuries from
occurring.
The position of the machine head can be adjusted
depending on the height of the workpiece or the
drill accessory length. Adjust the height of the
machine head so that there is sufficient clearance
between the tip of the drill bit (22) and the upper
surface of the workpiece. A clearance of ~15 mm is
recommended.
1. Loosen the clamping lever (36) at the back
of the machine head with one turn in coun-
ter-clockwise direction.
2. Crank the height adjustment lever (33) clockwi-
se to move the machine head up.
3. Crank the height adjustment lever (33) counter-
clockwise to move the machine head down.
4. The height adjustment cannot be moved any
further once the upper or lower dead centre is
reached.
WWW.VONROC.COM
Publicidad
