Publicidad
Idiomas disponibles
Idiomas disponibles
EN
6.2
HANDLING
a
Be careful when moving the appliance to avoid pos-
sible damages to it. The appliance should only be
unpacked once it has reached the installation site.
The appliance must be lifted and handled exclusive-
■
ly using suitable lifting equipment with adequate
load-bearing capacity for the weight to be lifted;
check the data of the label on the packaging.
Be careful since the appliance tends to unbalance,
■
because its centre of gravity is shifted towards the
front.
Adequately protect wooden or parquet flooring to
■
prevent it from getting damaged.
In order to prevent accidents or damages to the product, strictly ob-
serve the following recommendations:
- when shifting the packaging, perform slow and continuous movements
- do not tilt the packaging too far so as to prevent the product from
tipping over
- the area where the product will be handled must be carefully
cleaned and free from any type of hindrance.
6.3
UNPACKING
a
When removing the packaging, be careful to avoid
scratching or damaging the product.
Do not disperse packaging material in the envi-
■
ronment or leave it within reach of children, as the
packaging may be potentially dangerous. It must
therefore be disposed of according to the current
legislation.
Remove from the appliance the accessories and any
■
polystyrene or cardboard parts used to secure the
moving parts.
When handling any steel parts, we suggest wearing
■
clean cotton gloves to avoid leaving fingerprints on
the product which could be difficult to remove during
cleaning.
To remove the appliance from its transport support (pallet):
- for model STARBOX 650 it is necessary to remove the combustion
chamber (see paragraphs
"Removing the fume
tracting the combustion
chamber") and loosen the screws fasten-
ing the appliance to the pallet; for model STARBOX 750 only the
screws on the fixing plate must be removed
- lift the appliance using equipment suited to its weight
- remove the transport support (pallet).
14
adapter" and
"Ex-
STARBOX 650
x4
STARBOX 750
x4
Fig. 9
6.4
POSITIONING THE APPLIANCE
l
Before positioning the appliance:
make sure that the chosen site is suitable for the
■
product's placement and operation; carefully read
the information and specifications contained in the
section
"Configuration for
make sure that the air nozzles are configured on the
■
basis of the type of combustion air draw (consult the
paragraph
"Connecting the combustion
chosen ducting system (consult the paragraph
stalling the
kit"); also consult the product's technical
sheet for information on their correct sizing and po-
sitioning.
The insert can be positioned in an existing fireplace or in a newly built
fireplace with suitable lining.
To position the insert correctly, it is essential:
- that the fireplace respects the minimum safety clearances, as indi-
cated in the chapter
"Minimum safety
- that the support base is suitably sized for housing the insert
- that the material with which the support base is made is capable of
withstanding the insert's weight
- to use fastening systems suited to the material used to make the
support; screws and plugs are not supplied and must be sized by
the installer
- make the convective air inlet and outlet openings valid for all types
of installation systems proposed:
- convective air inlet minimum cross-sectional size = 400 cm
- convective air outlet minimum cross-sectional size = 400 cm
Positioning in exciting fireplace
To install the insert in an existing fireplace, proceed as follows:
- remove the combustion chamber (1) completely – see paragraphs
"Removing the fume
adapter" and
chamber"
- insert the outer shell (2) into the existing fireplace, level it and fas-
ten it using the holes (3) present on the lower part (STARBOX 650)
or on the fixing plate (STARBOX 750)
STARBOX 650
x4
3
1
INSTALLATION
installation"
air") and the
"In-
clearances"
2
2
"Extracting the combustion
2
STARBOX 750
3
x4
Fig. 10
CS.STB.IST-1_EN_Rev.1.0_08-23
Publicidad
