Publicidad
Idiomas disponibles
Idiomas disponibles
39.
Fit the pod filter (18) into the filterholder (8) that has been warmed up by leaving it attached to the brewing group
as described in point 7.
40.
Before preparing your coffee, it is advisable to position the coffee/hot water/steam lever switch (13) on coffee
mode (down) and lift the pump lever switch (26) to dispense water for 5 seconds from the brewing group (5) with
the tightened filterholder (8) into the drip tray. After dispensing water for the indicated time, lower the pump lever
switch (26) in order to stop the purge.
41.
Open the single packed pod not damaging the pod.
42.
Place the pod in its filter (18).
43.
Insert the filterholder (8) into the brewing group (5), turn it from left to right with force, then put the cup on the
removable drip tray grate (7).
44.
Position the lever switch (13) on coffee and lift the pump switch (26). The pressure value on the manometer (25)
should reach the green zone during the extraction.
45.
Once you get the desired quantity of coffee, push the pump switch (26) down again.
46.
Remove the filterholder (8) and throw the used pod away and reposition the filterholder in the brewing group (5)
to warm up again.
Steam:
47.
Check that the water tank (1) has been filled in with water by looking at the water level indicator.
48.
Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the
machine is off. If it's on, proceed to the next step.
49.
Position the lever switch (13) on steam mode. NB: the PID's display will automatically show the writing STE and
alternatively the set temperature degree for steam. The PID is already set from the producer on 125°C, i.e. the
ideal temperature for steam distribution. (If you want to change the PID's temperature, please follow the
instructions written under How to set the temperature inside the boiler by means of the PID).
50.
As soon as the light (14) goes on, the machine is ready for use.
51.
Open the steam/hot water knob (4). First some water will flow out and then the steam.
52.
Put the cup with the desired infusion under the steam wand (6) and turn the knob (4) completely.
53.
When the drink has been suitably frothed, close the steam/hot water knob (4).
54.
IMPORTANT: after you have frothed your milk, reopen the steam/hot water knob (4) and position the steam
switch (13) on hot water, and lift the pump switch up (26). When the water flows out of the steam wand (6), close
the steam/hot water knob (4) again and at the same time push the pump switch down (26) and re-position the
switch (13) on coffee again. Clean carefully the steam/hot water tube (6). This operation is needed in order to
restore the water circuit inside the machine tubes.
Hot water:
55.
Check that the water tank (1) has been filled in with water by looking at the water level indicator.
56.
Press the on/off switch (11): the indicator light of the switch (11) will come on. Do this operation only if the
machine is off. If it's on, proceed to the next step.
57.
Position the lever switch (13) on hot water mode.
58.
As soon as the PID's display (27) shows the set temperature and the indicator light (14) goes on, the machine is
ready for use.
59.
Before preparing your hot drinks, it is advisable to open the steam/hot water knob (4), turn the lever switch on
hot water (13) and lift the pump switch (26). Hot water coming is dispensed from the steam/hot water wand (6)
immediately. Dispense water into the drip tray for 5 seconds. After that lower the pump switch (26), then close
the steam/hot water knob (4).
60.
Put an empty cup under the steam/hot water wand (6), open the steam/hot water knob (4) and lift the pump
switch (26).
61.
Hot water is dispensed from the steam wand (6) immediately.
62.
Once you have got the desired quantity of water, lower the pump switch (26) again and close the steam/water
knob (4).
63.
After obtaining hot water from the wand (6), make sure that there is still water in the tank (1).
HOW TO SET THE BOILER TEMPERATURE BY MEANS OF THE PID:
The PID has been set by the producer of this machine on a temperature of 95°C for coffee mode and on 125°C for
steam mode. In order to change the temperatures please proceed as follows:
press the button
-
95°C
press the button
-
125°C
as soon as the display shows the writing t1 or t2 press the button
-
temperature. NB: in order to change the temperature's value, it's necessary to press the button
and only afterwards you can help yourself with the buttons
temperature, decreasing or increasing it.
after 3 sec. from pressing the last button, the inserted temperature is memorized, and the display shows the set
-
temperature for coffee or steam.
the temperature's value can be set starting from a min. of 80C° up to a max. of 130C° for coffee mode and from
-
a min. of 120°C up to a max. of 140°C for steam mode. NB: the display will flash while changing from steam
mode to coffee mode and it will automatically stop only after reaching the set temperature for coffee mode.
Useful Tips:
The filters (9, 10, 16 and 18) do not need to be washed after every single use but we suggest checking that the holes
−
are not obstructed.
Pag. 12
once: the display will show the writing "t1" that refers to the coffee thermostat set on
twice: the display will show the writing "t2" that refers to the steam thermostat set on
to change the previously set
and
in order to set the desired
English
first
Publicidad
