Publicidad
Idiomas disponibles
Idiomas disponibles
TFA_No_35.1083_Anleit_01_24
Wireless weather station
1. Time alarm (hours/minutes, at high alarm setting mode, the same
time alarm setting sequence will repeat)
2. Indoor humidity low alarm
3. Indoor temperature low alarm
4. Outdoor humidity low alarm
5. Outdoor temperature low alarm
6. Dew point
7. Pressure low alarm
•
Remark: After the initial pressing of "ALM" button, "- - -" will be dis-
played for all segments. Later the high and low alarm values appear if
they are activated.
7.5.1 Alarm signal
•
When a set weather alarm condition has been triggered, that particular
alarm will sound for 120 seconds. The corresponding value, "HI AL" or
"LO AL" and the alarm symbol are flashing until the weather condition
does not meet the user set level. Press any key to mute the alarm.
•
Example:
Dew point high alarm was triggered:
digit flashing
7.5.2 Alarm clock function
•
In the Alarm-Mode HI or LO you can adjust the alarm time. Press "SET"
button.
•
The hour digit is flashing. Press "+" or "MIN/MAX" button to adjust the
hours. Press "SET" button again for to set the minutes.
•
Press "ALM" button to switch the alarm off (the alarm symbol disap-
pears) or on. Confirm with the "SET" button.
•
When alarm is sounding, press any button to stop the alarm.
•
Once the alarm starts to ring, you can activate the snooze function by
pressing the top button "SNOOZE/LIGHT". The alarm will be interrupted
for 10 minutes.
7.6 Backlight
•
Press the top button "SNOOZE/LIGHT". The backlight will light for 10
seconds.
8. Positioning of base station and transmitter
•
With the foldable leg at the back of the unit, the base station can be
placed onto any flat surface or wall mounted at the desired location by
the hanging hole at the back of the unit. Avoid the vicinity of any inter-
fering field like computer monitors or TV sets and solid metal objects.
•
Choose a shady and dry position for the transmitter. (Direct sunshine
falsifies the measurement and continuous humidity strains the elec-
tronic components needlessly)
22
18.01.2024
14:45 Uhr
Seite 12
digit flashing
digit flashing
Wireless weather station
•
Check the transmission signal from the transmitter to the base station
(transmission range 100 m free field). Within ferro-concrete rooms
(basements, superstructures), the received signal is naturally weak-
ened.
•
If necessary choose another position for transmitter and/or base sta-
tion.
•
To wall mount the transmitter, use 3 screws to affix the wall bracket to
the desired wall, plug in the transmitter to the bracket (D2).
9. Care and maintenance
•
Clean the instrument and the transmitter with a soft damp cloth. Do not
use solvents or scouring agents.
•
Remove the batteries if you do not use the product for a long period of
time.
•
Keep the instrument in a dry place.
9.1 Battery replacement
•
Please note: When the batteries are changed, the contact between
transmitter and receiver must be restored – so always insert new bat-
teries into both units.
10. Troubleshooting
Problems
Solution
➜ Ensure correct polarity of the batteries
No indication
➜ Change the batteries
on the weather station
➜ No transmitter installed
No transmitter reception
➜ Check batteries of external transmitter
Display "---"
(do not use rechargeable batteries!)
➜ Restart the transmitter and weather
station according to the manual
➜ Choose another place for the trans-
mitter and/or the weather station
➜ Reduce the distance between the
transmitter and the weather station
➜ Check if there is any source of inter-
ference
➜ Choose another place for the weather
No DCF reception
station
➜ Manual time setting
➜ Wait for attempted reception during
the night
➜ Change the batteries
Incorrect indication
If your device fails to work despite these measures, contact the retailer
where you purchased the product.
23
Publicidad
