Publicidad
Idiomas disponibles
Idiomas disponibles
TFA_No_35.1083_Anleit_01_24
Wireless weather station
• Batteries must not be thrown into a fire, short-circuited, taken apart or
recharged. Risk of explosion!
• Low batteries should be changed as soon as possible to prevent damage
caused by leaking.
• Never use a combination of old and new batteries together, nor batteries
of different types.
• Avoid contact with skin, eyes and mucous membranes when handling
leaking batteries. In case of contact, immediately rinse the affected areas
with water and consult a doctor.
Important information on product safety!
• Do not expose the device to extreme temperatures, vibrations or shocks.
• Protect it from moisture.
• The outdoor transmitter is protected against splash water, but is not
watertight. Choose a shady and dry position for the transmitter.
5. Elements
5.1 Receiver (base station) Fig. 1
LCD
1.
DST (Daylight Saving Time)
2.
Radio-controlled time DCF
3.
Time
4.
Radio-controlled time icon
5.
Alarm on indicator
6.
Day of week/ time zone
7.
Date
8.
Indoor humidity display in % RH
9.
Indoor temperature and humidity low alarm and high alarm
10.
Indoor temperature display
11.
Indoor temperature display unit in °C/°F
12.
General indoor alarm icon
13.
Outdoor transmitter signal
14.
MIN/MAX information
15.
Dew point temperature display
16.
Outdoor humidity unit in % RH
17.
Outdoor temperature and humidity low alarm and high alarm
18.
Outdoor temperature display unit in °C/°F
19.
Outdoor temperature display
20.
General outdoor alarm icon
21.
Weather forecast icon
22.
Weather tendency indicator
23.
Pressure alarm on indicator HI
24.
Pressure unit (relative or absolute)
25.
Pressure alarm on indicator LO
26.
Pressure history graph of the last 24 hours
27.
Pressure display
16
18.01.2024
14:45 Uhr
Seite 9
Wireless weather station
28.
Pressure display unit (inHg or hPa)
29.
Pressure alarm on indicator
Buttons
B1:
"SET" button
B2:
"ALM" button
B3:
"MAX/MIN" button
B4:
"+" button
B5:
"SNOOZE/LIGHT" button
Housing
C1:
Wall mount hole
C2:
Battery compartment
C3:
Stand (fold out)
5.2. Sensor unit (Transmitter) Fig. 2
D1:
Outdoor temperature and humidity
D2:
Wall bracket
D3:
Battery compartment
6. Getting started
6.1 Battery installation
•
Take the transmitter out of its holder and open the battery
compartment of the base station and the transmitter (screwed) and
place both instruments on a desk with a distance of approximately 1.5
meter. Check that no other electronic devices are close.
•
Insert 2 x AAA 1,5 V batteries first into the battery compartment of the
transmitter and immediately afterwards 3 x AA 1,5 V in the base station,
observing the correct polarity.
6.2 Reception of outdoor values and DCF time
•
When the base station is powered up, a short beep will sound and all
LCD segments will light up for about 3 seconds before it enters into
learning mode to learn the transmitters security code.
•
After the transmitter is powered up, it will transmit the temperature and
humidtiy and then the transmitter will start radio-controlled time recep-
tion. During the DCF time reception period (max. 10 minutes), no
weather data will be transmitted.
•
Note: DO NOT PRESS ANY KEY during the first 10 minutes learning
period or before radio-controlled time is displayed on the receiver. After
both outdoor values and radio-controlled time are displayed you can
place your transmitter outdoors at the final destination. In case the
clock cannot detect the DCF-signal (for example due to disturbances,
transmitting distance, etc.), the time can be set manually. If the outdoor
weather data is not displayed or if any button is pressed before the
weather station receives the signal, or when changing batteries you will
need to follow the battery installation procedure again.
Please wait minimum 10 seconds before inserting the batteries
again to make a proper reset for both transmitter and receiver.
17
Publicidad
