Whirlpool W11I OP1 4S2 H Manual Del Usuario página 8

DESCALE
This special function, activated at regular intervals, allows you
to keep the boiler and the steam circuit in the best condition.
A message will be shown on display, to remind you to execute
this operation regularly. Descale requirement is triggered by
the number of steam cooking cycles performed or steam boiler
working hours since the last descale cycle (see the table below).
"PLEASE DESCALE" MESSAGE appears
after
15 cycles of steam cooking
22 hours of steam cooking duration
20 cycles of steam cooking
30 hours of steam cooking duration
The descaling procedure can also be performed whenever the
user desires a deeper cleaning of the reservoir and the internal
steam circuit.
The average duration of the full function is around 185 minutes.
Once the function is started, follow all the steps indicated on
the display.
Please note: The function can be paused but, if it is canceled at any
time, the entire descaling cycle must be repeated from the
beginning.
PHASE 1.1: DRAINING (UP TO 3 MIN.)
»
If the reservoir is not empty, the draining phase has to be
performed before starting the proper descaling process. In this
case, please proceed with the draining task as described in the
dedicated Drain paragraph. Instead, if the reservoir does not
contain water, the appliance will skip automatically to PHASE
1.2.
Please note: to ensure that the water is cold, it is not possible to
perform this activity before 4 hours have elapsed from the last
cycle (or the last time the product was powered). During this
waiting time, the display will show the following feedback "WATER
IS TOO HOT - wait until the temperature decreases". The jug must
be at least 2 liters large.
» PHASE 1.2: DESCALING (~120 MIN.)
When display will ask you to prepare the solution, proceed
adding 3 sachets (corresponding to 75g) of the specific Oven
WPRO descaler in 1,7 liters of drinking water at ambient
temperature.
1
1,7 Liters
Once the descaling solution is ready, press DONE and connect
the pipe following the instructions on the display, then press
START. The pump will stop its operation when the reservoir will
be fully loaded; then the system is ready to start the main
descaling process.
8
WHAT TO DO
Descale is recommended
It is not possible to run
a Steam cycle until a
Descale cycle will be
carried out
= 75 g
+ 2 + 3
The descaling phases do not need you to stay in front of
the appliance. After each phase is completed, an
acoustical feedback will be played and the display will
show instructions to proceed with the next phase.
PHASE 1.3: DRAINING (UP TO 3 MIN.)
»
When the display will ask you to place a container below the
draining hole, please proceed with the draining task as
described in the dedicated Drain paragraph.
PHASE 2.1: WATER REFILLING
»
To clean the reservoir and the steam circuit, the rinse cycle has
to be done.
Fill a container with 1,7 L of clear drinking water, then connect
the pipe following the instructions on the display and press
START. The pump will stop its operation when the reservoir will
be fully loaded. Unplug the pipe and close the door.
PHASE 2.2: RINSING (~65 MIN.)
»
The system is now ready to start the final rinsing process.
» PHASE 2.3: DRAINING (UP TO 3 MIN.)
After the last draining operation, the message "Descale
Completed" will appear on the display: press DONE to confirm.
It will be now possible to use all the steam functions.
*WPRO descaler is the suggested professional product for the
maintenance of the best performance of your steam function in
the oven. Please follow the instructions for use on the packaging.
For orders and information contact the after sales service or www.
whirlpool.eu
Whirlpool will not be held responsible for any damage caused by
the use of other cleaning products available on the market.
MUTE
Tap the icon to mute or unmute all the sounds and alarms.
CONTROL LOCK
The "Control Lock" enables you to lock the buttons on the
touch pad so they cannot be pressed accidently.
To activate the lock:
• Tap the icon.
To deactivate the lock:
• Tap the display.
• Swipe up on the message shown.
MORE MODES
For selecting Sabbath mode and accessing Power
Management.
PREFERENCES
For changing several oven settings.
WI-FI
For changing settings or configuring a new home network.
INFO
For switching off "Store Demo Mode", resetting the product to
factory default settings and obtaining further information
about the product.