Electrical Connections; Extension Leads; Machine Description (Fig. 2-3); Technical Specifications - Fox D 305 Manual De Instrucciones

Serial number / Year of production
No access - Danger zone

ELECTRICAL CONNECTIONS

ELECTRICAL CONNECTIONS
Use 230 V 50 Hz alternate voltage to supply your machine.
Ensure that the power supply corresponds to this voltage,
that it is protected by a differential and magnetothermal
switch, and that the earthing system is effi cient. If your
machine does not work when connected to a socket, check
carefully the power supply features.

EXTENSION LEADS

Only use three conductors extension cables, with a plug
with two plugs and a earthing contact and sockets with
two holes and a earth corresponding to the plug of the
tool. When using an electric tool at a remarkable distance
from the power supply, use an extension lead with suffi cient
dimensions to transport the current which the tool needs.
If the extension lead has not the suffi cient dimensions a
voltage drop can occur, thus causing an overheating and
a voltage loss. You can only use extension leads which are
in compliance with CE standards.
Extension lead length: .....................................up to 15 m
Cable dimensions: .........................................3 x 2,5 mm²
Before using any kind of extension lead, check that it has not
bare wires and that the insulation is not cut or worn. Repair
and change immediately it if it is damaged or worn.
WARNING:
Extension leads must be arranged away from the
working area in order that they do not come into
contact with the workpieces, the tool or other
parts of the machine, thus creating possible
risks.
WARNING:
KEEP THE TOOLS AND THE EQUIPMENT AT A
SAFE DISTANCE FROM CHILDREN
WARNING:
Your mitre-saw's electrical system is equipped
with an undervoltage relay which automatically
opens the circuit when the voltage falls below
a minimum pre-established limit and which
prevents the self-reset of the machine functions
when voltage returns to normal levels. If the
machine stops involuntarily, do not be alarmed
and make sure that there has not been a voltage
failure in the electrical system.

MACHINE DESCRIPTION (Fig. 2-3)

The mitre-saw machine consists of three basic parts: the
machine body complete with motor 6, which is integrated
into the base 3 by means of the joint 4 and the swivel support
5, and the upper work unit, consisting of the workbench 12,
the rest square 14 and the movable protective cap 13.
The base 3 is used as a support when cutting and butting
operations have to be carried out in the different available
angles; the upper table is used as a support when trimming
or sectioning large planks of wood, and especially when
cutting wood along the grain.
SUITABLE USE
It can cut:
a. HARD AND SOFT, DOMESTIC AND EXOTIC WOOD
BOTH LONGITUDINALLY AND TRANSVERSALLY;
and with appropriate adjustments (specific blade and
clamps only in mitre saw mode):
- PLASTICS
- ALUMINIUM AND ALUMINIUM ALLOYS
UNSUITABLE USE
- Do not cut FERROUS MATERIALS, STEEL AND CAST
IRON OR ANY OTHER MATERIAL NOT MENTIONED
ABOVE AND IN PARTICULAR FOODSTUFFS.
- Do not use it as a CIRCULAR SAW WITHOUT
PROTECTION.

TECHNICAL SPECIFICATIONS

Engine power:..................................................2000 W S1
Voltage and frequency: ................................230 V - 50 Hz
Speed: ..............................................................4200 RPM
Saw blade maximum dimensions:.....305x30X2,8 mm (40 teeth)
Crosscut at 90°: .......................................... 185 X 85 mm
Oblique cutting 45°: ..................................... 125 X 85 mm
Inclined cutting 45°: ..................................... 185 X 60 mm
Oblique cutting 45°: ........................................90 x 40 mm
Left and right stops: ............................... 0° - 45° every 5°
Inclination stops: ................................................ 0 and 45°
Net weight:.............................................................17.5 kg
Gross weight:............................................................19 kg
Hand-arm vibration: ......................................< 2,5 m/sec2

NOISE CONDITIONS

The noise emitted, measured in conformity with the
standards EN61029, EN3744 and EN11201 is:
- Sound pressure level ........................ LpA = 100 dB(A)
- Sound power level ........................... LWA = 113 dB(A)
- Uncertainty of measurement K .............................. 3 dB
We recommend you to use ear protection devices.
15