Publicidad
Idiomas disponibles
Idiomas disponibles
Pre-Installation
PLANNING INSTALLATION
Before you begin assembly, locate the instructions and hardware. Compare all parts with the Hardware Included and Package Contents lists. Be
sure you have all the parts and can identify them. A helping hand is always good. Assemble your fireplace with an adult assistant if possible.
Some pieces are heavy and will need to be held by a helper. Assembly time will take approximately 5-20 minutes.
Before assembly, use scissors to unwrap the parts from the packaging. Do not use a box cutter or exacto-knife, as you may cut into the heater
pieces inside the box and damage the finish. Check for the red hardware bag located inside the packaging, taped to the top of the box. Do not
discard any pieces. Use an appropriate screwdriver to insert and tighten all screws.
CAUTION: This carton includes a GLASS panel! Always use extreme caution when handling glass.
Failure to do so could result in personal injury or property damage.
SPECIFICATIONS
Model No .
Wall Mounted Dimensions W x D x H
Stand Mounted Dimensions W x D x H
Weight
Voltage
Frequency
Watts / Amps
WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical
shock, and injury to persons.
WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace
and replace any part of the electrical system which has been under water.
GROUNDING INSTRUCTIONS
• Always connect to properly grounded outlets.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners
or the like. Arrange the cord away from heavily trafficked areas, where it
will not be tripped over.
• Always plug heaters directly into a wall outlet/receptacle. Never use with an
extension cord or a relocatable power tap (outlet/power strip).
• There is a resettable cutout switch inside the heater. Should the heater
overheat, the cutout will turn the fireplace heater off. To reset the cutout
switch, unplug the unit and wait 5 minutes before plugging it back in.
• The remote control contains a small battery. Keep away from children. If
swallowed, seek medical attention immediately.
CAUTION:
If you need to continuously reset the cutout,
unplug the unit and call Technical Support.
4
320-42C-10
106.7 cm x 12.8cm x 46.0cm
(42in x 5in x 18 1/8in)
106.7 cm x 27.6cm x 52.9cm
(42in x 10 7/8in x 20 7/8in)
14kg (30.8lbs)
120V
60 Hz
1400 W / 12 A
ELECTRICAL CONNECTION
A 15 Amp, 120 Volt, 60 Hz circuit with a properly grounded outlet
is required to operate this appliance. Preferably, the appliance
will be on a dedicated circuit, as other appliances on the same
circuit may cause the circuit breaker to trip or the fuse to blow
when the fireplace is in operation. The unit comes standard
with a 6 ft (1.8 m) long 3-wire cord, exiting out the back of the
fireplace. Plan the installation to avoid the use of an extension
cord. If an extension cord must be used, it must be a minimum
No. 14 AWG, 3-wire with grounding type plug and connector,
and must be rated not less than 1875 watts. The extension cord
shall not be more than 20 ft (6 m) in length.
(A)
GROUNDING
PIN
ADAPTER
GROUNDING
MEANS
(C)
NOTE:
Adapters are NOT for use in Canada.
This heater is for use with 120 volts. The cord has a plug
as shown at (A) in Figure 1. An adapter as shown at (C) is
available for connecting three-blade grounding-type plugs
to two-slot receptacles. The green grounding lug extending
from the adapter must be connected to a permanent ground
such as a properly grounded outlet box. The adapter should
not be used if a three-slot grounded receptacle is available.
Figure 1
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
(B)
GROUNDING
PIN
(D)
Publicidad
