Publicidad
Idiomas disponibles
Idiomas disponibles
3.5
Setting main operating mode
Switching the appliance on/off
▶ Press the K key to switch the device on or off:
The unit starts in the set operating mode or switches off. To protect
the unit it can only be switched back on after some time has passed.
Settings can also be made when the appliance is switched off. The
device saves the settings, and also retains them in the event of a power
failure.
After it has been switched off, the unit remains in standby mode.
Following a power failure the unit restarts automatically. This can lead to
conflicting readings on the displays which are resolved automatically
during operation.
Automatic mode
In automatic mode, the unit switches automatically between heating,
cooling, fan and dehumidification mode, depending on the set
temperature.
▶ Press the Mode key repeatedly until
▶ Select the required temperature with the . and / keys.
The fan speed cannot be adjusted in automatic mode.
Cooling mode
▶ Press the Mode key repeatedly until
▶ Press the
key until the required air speed is reached.
▶ Select the required temperature with the . and / keys.
Fan (Only) Mode
▶ Press the Mode key repeatedly until
▶ Press the
key until the required fan speed is reached. AUTO can
be selected to enable automatic control.
The temperature cannot be adjusted or displayed in fan mode.
Dehumidification mode
▶ Press the Mode key repeatedly until
▶ Set the required temperature with the . and / keys.
The fan speed cannot be adjusted in dehumidification mode.
Heating mode
▶ Press and hold the Mode key until
▶ Set the required temperature with the . and / keys.
▶ Press the
key until the required air speed is reached.
If the outside temperature is very low, the heating capacity of the air
conditioning system may not be sufficient. We recommend connecting
additional heat sources.
Climate 5000i M – 6721849824 (2022/04)
appears on the display.
appears on the display.
appears on the display.
appears on the display.
appears on the display.
3.6
Louvre position memory
When the appliance restarts after a power failure, the louvres
automatically revert to the position that was previously set. Press the
Manual operation key on the indoor unit to restore the setting of the
louvres.
Following adjustment, the angle of the horizontal louvres should not be
too small, as otherwise condensate may form and drip into the
appliance.
3.7
Setting timer
ON and OFF timers can be set to between 0 and 24 hours, in 30-minute
increments for the first 10 hours, then in 1-hour increments. If 0 hours
is set, the timer is cancelled.
Setting the on timer
▶ Press the
key until the
▶ Press the . or / key to set the desired time.
The setting is applied shortly afterwards.
Setting the off timer
▶ Press the
key until the
▶ Press the . or / key to set the desired time.
The setting is applied shortly afterwards.
Cancelling timer
▶ Press the
key to select the corresponding timer.
▶ Set 0.0 hours.
The timer is cancelled after a short time.
Combining timers
The two timers can be set at the same time. Either timer can be
programmed to activate prior to the other
▶ Set the on timer and off timer.
The settings will be automatically combined.
Current time
Setting of ON timer
Setting of OFF timer
Switch-on time
Switch-off time
Table 7 Example
You can not program the on timer and off timer to operate the unit at
different temperatures or with other settings.
3.8
Other functions
3.8.1
Setting the swing function
NOTICE
If the louvre remains at the lowest position during cooling mode for an
extended period, condensate may be discharged. Adjusting the louvre
by hand may cause faults.
▶ Only use the remote control to adjust the louvre.
Automatic vertical Swing mode (up/down)
▶ Press the Swing key until the symbol
▶ To cancel the automatic vertical Swing mode: press the Swing key
again.
Operation
symbol appears.
symbol appears.
13:00 o'clock
4.0 h
8.5 h
17:00 o'clock
21:30 o'clock
appears.
43
Publicidad
