Publicidad
Idiomas disponibles
Idiomas disponibles
Timer to close
Description of the operation:
The garage door opener closes the garage door automatically from
the fully open position after a pre-programmed period of time.
For this, the Liftmaster safety light barrier must be connected to the
garage door opener according to EN60335-2-95.
Activating:
1. Press the P button and the MINUS (-) button simultaneously for about
3 seconds.
2. When you release the buttons, the LED next to the S button turns on
and the operator lighting flashes twice as confirmation that the garage
door opener is in programming mode.
3. Each time you press the PLUS (+) button the time period increases
by 10 seconds. Maximum 180 seconds are possible (= pressing 18
times).
4. Each time you press the MINUS (-) button the time period reduces
again by 10 seconds (up to a minimum of 10 seconds).
5. To save the desired time period, press the P button. To confirm the
programming, the operator lighting flashes once.
Disabling:
1. Press the P button and the MINUS (-) button simultaneously for about
3 seconds.
2. The operator lighting will flash twice to confirm that the garage door
opener is in the disable mode.
3. Press P button once.
4. The operator lighting flashes once to confirm that the automatic clos-
ing function has been disabled.
Information:
• Automatic closing only works from the fully open position (garage door
must have reached the end position OPEN).
• If the light barrier is interrupted during closing, the garage door goes
back to the fully open position and remains there until the obstacle
has been removed and after the programmed time period has elapsed
again.
• Once the garage door opener is in programming mode, the next but-
ton press must be carried out within 30 seconds, or else the program-
ming mode is cancelled. In this case, the operator lighting flashes five
times.
• If the time period needs to be subsequently changed, for example,
from 60 to 80 seconds the PLUS (+) button must be pressed eight
times in the programming mode, as every new programming starts at
0 seconds.
Troubleshooting:
The garage door opener does not operate without the light barrier.
No error! Connecting the light barrier once is absolutely necessary.
Cycle counter
The garage door opener can display the number of cycles (OPEN/
CLOSE = 1).
1. Disconnect garage door opener from power supply
2. Press and hold the P and S buttons
3. Connect the garage door opener again while the buttons are still
pressed
4. After all three LEDs have flashed once and the operator lighting is
switched on, the LED near the S button starts flashing after approxi-
mately 5 seconds (once every 1000 cycles). Release the buttons.
21
Cleaning and maintenance
Before any maintenance, cleaning and related
maintenance work, the mains supply plug should be
pulled out. Danger from electric shock!
Maintenance of the door opener
A proper installation ensures the optimum performance of the door
opener with minimum maintenance. An additional lubrication is not
required. Gross dirt accumulation in the guide rail may impair the
function and must be removed.
22
Cleaning
Clean the drive head, wall switch and handheld transmitter with a soft,
dry cloth..
Do not use liquids.
23
Maintenance
Check the system often, especially cables, springs and
fasteners, for signs of wear, damage or lack of balance.
Do not use if repair or adjustment work must be performed,
because an error in the system or an incorrectly balanced
door may cause injury. Repairs to electrical equipment and gates may be
carried out only by an authorized specialist / expert. In any case, please
do not ever carry out repairs yourselves because this could result in
serious injury or death.
Once a month:
• Check automatic safety reverse again and reset if necessary.
• Operate door manually. If the door is unbalanced or stuck, please
contact the service centre.
• Check for complete opening and closing of the door.
Where appropriate, readjust limit switches and / or power.
Twice a year:
• Check the belt tension. For this, first disconnect the carriage from the
drive. If necessary, adjust belt tension.
Once a year (at the door):
• Lubricate door roller, bearings and joints. An additional lubrication of
the door opener is not required.
Do not grease the door rails!
Limit switch adjustment and force regulation:
These settings must be checked and undertaken properly during the
installation of the opener. Due to weathering, minor changes can occur
during operation of the opener that need to be addressed by a new
setting.
This can particularly happen in the first year of operation.
Follow the instructions for setting limit switches and traction (see 17)
carefully and re-check the automatic safety reverse after each
resetting.
24
Replace batteries of the remote control
Battery of the remote control:
The batteries in the remote have an extremely long life. If the transmis-
sion range decreases, the batteries must be replaced.
Batteries are not covered by the guarantee.
Please observe the following instructions for battery:
Batteries should not be treated as household waste. All consumers are
required by law to dispose of batteries properly at the designated
collection points.
Never recharge batteries that are not meant to be recharged.
Danger of explosion!
Keep batteries away from children, do not short-circuit them or take
them apart. See a doctor immediately, if a battery is swallowed.
If necessary, clean contacts on battery and devices before loading.
Remove exhausted batteries from the device immediately!
Increased risk of leakage!
Never expose batteries to excessive heat such as sunshine,
fire or the like!
There is increased risk of leakage!
Avoid contact with skin, eyes and mucous membranes. Rinse the
parts affected by battery acid with plenty of cold water and consult
a doctor immediately.
Always replace all batteries at the same time. Use only batteries of the
same type; do not use different types or mix used and new batteries.
Remove the batteries if the device is not being used for a long time.
Replacing battery:
To replace battery, turn remote control around and open the case with a
screwdriver. Lift cover and lift control board below. Slide battery to one
side and remove. Watch polarity of battery!
Assemble again from in reverse direction.
ATTENTION!
Danger of explosion if battery is replaced improperly.
Replacement only by identical or equivalent type (CR2032).
en 6
Publicidad
