Publicidad
Idiomas disponibles
Idiomas disponibles
Before every mowing job, make sure that the motor stop safety control bar is
working perfectly. When the safety control bar is released, the cutter bar must come
to a standstill within 3 seconds.
After release, the safety control bar must always return to the position shown in the
"Description of components" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the blade motor, it rotates and a wind noise can be heard.
The stopping time corresponds to the duration of the wind noise after the motor
has been stopped; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
The correct operation of the autodrive control bar must also be checked before
each mowing job. When the autodrive control bar is released, the autodrive must
stop immediately and the mower must come to a standstill. If this is not the case, it
must be checked immediately by an authorised workshop.
Make sure that all protective devices have been attached properly and are not
damaged.
To avoid any risk, always check the condition and firm seating of the blade before
each mowing job. The blade fastening screw must always be tightened by an
authorised workshop. If the blade screw is tightened excessively or insufficiently,
the blade fastening and cutter bar may be damaged or get loose, which can lead
to serious injuries. A worn or damaged blade must imperatively be replaced (see
chapter "Maintenance of the cutter bar").
Check the blade fastening for wear and a tight fit every 10 operating hours Also
check device screws and nuts for a firm fit and re-tighten, if necessary.
If the mower becomes blocked e.g. by colliding with an obstacle, have an
authorised workshop check whether any parts of the mower are damaged or
deformed. Always have any necessary repairs done by an authorised workshop
too.
If the machine starts to vibrate unusually heavily or to make unusual noises, please
have it checked immediately by an authorised workshop.
Time restrictions
In Germany, the time for the operation of lawn mowers is regulated in the "32nd
Ordinance for the Implementation of the Federal Immissions Act (32. BImSch-V)".
In addition, regional restrictions are possible (e.g. to observe the afternoon quiet
hours); related information is available from the competent municipal authority.
Tips on caring for your lawn (figure M)
WARNING
Remove all foreign bodies (stones, wood, branches, etc.) from the lawn
before any mowing; however, you should still keep an eye out for objects
lying around while mowing.
You can get an introduction to lawn care from your dealer on request. Information
and instructions for mowing can also be found on the manufacturer's website.
Mulching
Your lawn mower can be equipped with a mulch kit. The corresponding conversion
kit to the mulch system is available from specialist dealers as an accessory (for the
order no. of the conversion kit, see "Original spare parts and accessories").
The mulch kit also includes tips and information on mulching. Information regarding
mulching can also be found on the manufacturer's website.
WARNING
Always have the mower converted to a mulch system by an authorised
specialist workshop. Due to an incorrectly assembled blade fastening or an
excessively or insufficiently tightened blade screw, the cutter bar may
become loose, which can lead to serious injuries.
Conversion to side discharge mower (figure F + N2 + R3)
–
Switch off the motor F, wait until the cutter bar comes to a standstill.
–
Remove the battery/batteries N2.
–
Remove the cover plate (1) on the right side of the housing R3.
To do this, loosen the two self-locking nuts (2) and remove the washers (3).
From the inside (cutting space), remove the two saucer-head screws (4) and
remove the cover plate R3.
Conversion of the mulching knife system is not necessary!
The cover plate (1) must be re-installed for the device to be used as mulching
mower again.
IMPORTANT
Before fitting the cover plate, switch off the motor, wait until the cutter bar
comes to a standstill, remove the battery/batteries, clean the channel and
remove any grass residue and dirt from the inside of the housing to ensure
that the plate can be seated firmly and correctly.
From the inside, fit the cover plate into the housing in such a way that both bore
holes in the cover plate match the bore holes in the housing. Insert both saucer-
head screws (4) into the bore hole from the inside (cutting space), place the
washers (3) and fasten in place with the two self-locking nuts (2).
WARNING
Never use the device with the baffle plate damaged or missing.
Always work with the baffle plate closed (folded down), even if the device
has been converted for mulching.
17
SERVICE INTERVALS
IMPORTANT
Avoid damage! Under extreme or unusual conditions, shorter servicing
intervals than the ones specified below may be necessary. If you establish
any problems, please contact an authorised workshop.
Carry out routine servicing on the machine in line with the following servicing
intervals.
Work must be carried out at the following servicing intervals in addition to the
maintenance work listed in these operating instructions.
Before initial use
•
Charge the battery/batteries according to the separate operating instructions
for the charger.
•
Check all screw connections for a tight fit.
•
Check the blade screw and have an authorised workshop tighten it, if
necessary.
•
Check whether the motor stop safety control bar is working properly.
•
Check whether the autodrive control bar is working properly.
•
Check that all protective devices have been attached properly and are not
damaged.
Before every operation
•
Check the lawn area and remove any objects, particularly live wires.
•
Check the area of the boundary wire (if an automatic mower is being used for
lawn care).
•
Check the charge level of the battery/batteries (see chapter "Battery level
indicator").
•
Check the condition and firm fit of the blade; have the blade screw tightened
by an authorised workshop, if necessary.
•
Check whether the motor stop safety control bar is working properly.
•
Check whether the autodrive control bar is working properly.
•
Check that all protective devices have been attached properly and are not
damaged.
•
Check grass collecting equipment for wear or loss of functionality.
•
Check that the air filter is clean and in good condition.
Every 10 operating hours
•
Check all screw connections for a tight fit.
•
Check the blade fastening for wear and a tight fit.
After every operation
•
Clean the mower.
•
Check the blades for damage and wear.
Every 50 operating hours
•
Clean the air filter W.
•
Grease the bearings of the rear wheel drive R.
During annual servicing
•
Have the air filter insert replaced W1.
•
Have the gearbox and the area under the belt cover cleaned.
•
Check all Bowden cables and have them set, if necessary.
18
CARE AND SERVICING FOR YOUR MOWER
Regular care is the best way to guarantee a long service life and problem-free
operation! Insufficient device maintenance will lead to safety-related faults!
Only use original spare parts because only those guarantee safety and
quality!
12
EN
Publicidad
