Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT
For cleaning and maintenance work, switch off the motor unit. To do this,
switch off standby mode (see chapter "SWITCHING STANDBY MODE
ON/OFF") and remove the batteries (1.), only then should you tilt the mower
upwards (2.) O. If it is necessary to place the mower on its side, place it on
the left side and not the right side, as otherwise the motor start on the upper
section of the bar might be actuated.
IMPORTANT
Never use a pressure cleaner or ordinary water jet to clean the motor.
Damage or expensive repairs can be the consequence.
The regular implementation of the prescribed maintenance and care work are the
prerequisite for a permanent and fault-free functionality of the motor and also the
basic requirement for any guarantee claims.
The motor should be kept clean, particularly on the outside, and the battery
compartment and ventilation slits must always be kept free from foreign bodies
(e.g. grass residue).
Perfect cooling can only be ensured when ventilation slits are always clean and
free from foreign bodies.
Cleaning and replacing the air filter (figure W + W1)
IMPORTANT
Never let the motor start or run whilst the air filter is removed.
–
Turn the locking switch on the air filter anticlockwise according to the symbol
(1) W.
–
Remove the air filter W1.
–
Clean the filter insert (2) every 50 operating hours W1.
In case of minor contamination, tap out gently on a smooth surface. In case
of severe contamination or damage, renew the filter(s). Do not wash out or
blast out the filter using compressed air and do not oil it.
–
After cleaning or replacement, insert the filter insert (2) into the air filter
plate (1).
The material must lie flat on all sides without any creasing or folds W1.
–
Insert the air filter correctly into the motor unit.
–
Press the locking switch on the air filter and turn it clockwise according to the
symbol (2) to lock the air filter in place W.
In the case of unfavourable operating conditions (severe formation of dust),
cleaning is required after every mowing job. Replace the filter insert annually or
every 100 operating hours.
(For filter insert order no., see chapter "Original spare parts and accessories")
20
TROUBLESHOOTING
Faults
Possible causes
Start routine not performed
Motor
does
not
correctly
start
Battery not charged
Battery not functional or
cannot be charged
Cutting height set too low
(when the grass is too high,
this prevents the motor
from starting up)
Remedy
Press the on/off button on
the motor unit to switch on
standby mode.
Press and hold the button on
the top bar within 120
seconds.
Turn over the safety control
bar.
The blade motor and blade
start up.
The button (2) can then be
released while the safety
control bar must be kept in
that position so that the blade
continues to run.
Once the device is in standby
mode (step 1), steps 2 and 3
are sufficient for restarting
the blade motor.
Charge the battery (see the
separate
operating
instructions for the charger).
Replace the battery.
Set a higher cutting height I.
Tilt the
machine
when
starting.
14
Too much grass waste in
the housing or ejection
channel
Air filter soiled
Bowden cable elongated
Cutting height too low
Motor switches off
during mowing
Battery pack is drained
Too much grass waste in
the housing or ejection
channel
The cutter bar is blunt
Motor
power
decreasing
Battery voltage low
Too much grass waste in
the housing or ejection
channel
Air filter soiled
Mower does not run Autodrive control bar not
pulled
Speed setting was made
while the motor was not
running
Belt has dropped off
Speed setting was made
Travel speed
while the motor was not
cannot be adjusted
running
Belt has dropped off
Extreme vibration
The cutter bar is blunt
Poor cutting,
lawn turns yellow
Cutting height too low
Motor speed too low.
EN
Clean grass from the cutting
space / ejection channel
(remove the battery/batteries
first N2 !).
Clean or replace the air filter
insert W + W1.
Have it checked by an
authorised workshop and
adjusted if necessary.
Have it checked by an
authorised workshop.
Set a higher cutting height
I.
Charge the battery (see the
separate
operating
instructions for the charger).
Clean grass from the cutting
space / ejection channel
(remove the battery/batteries
first N2 !).
Have it resharpened and
balanced by an authorised
workshop Q.
Charge the battery (see the
separate
operating
instructions for the charger).
Clean grass from the cutting
space / ejection channel
(remove the battery/batteries
first N2 !).
Clean or replace the air filter
insert W + W1.
Pull up the autodrive control
bar G.
With the motor running, turn
the speed setting to the
highest setting and then, also
with the motor running, set it
to the lowest level.
The speed may only be
adjusted while the motor is
running to prevent any
damage!
Have it checked by an
authorised workshop.
Have it checked by an
authorised workshop.
With the motor running, turn
the speed setting to the
highest setting and then, also
with the motor running, set it
to the lowest level.
The speed may only be
adjusted while the motor is
running to prevent any
damage!
Have it checked by an
authorised workshop.
Have it checked by an
authorised workshop.
Have it checked by an
authorised workshop.
Have it resharpened and
balanced by an authorised
workshop Q.
Set a higher cutting height I.
Switch
from
"ECO"
to
"TURBO"
(see
chapter
"CHANGING THE MOTOR
SPEED
(SWITCHING
ENERGY-SAVING
MODE
ON/OFF)")
Publicidad
