Roger Technology B71/BCHP Instrucciones Y Advertencias Para El Instalador página 11

3. wait 3 minutes to discharge the motor circuit voltage
4. remove B71/BCHP from the connector
5. replace the fuse
6. re-energize the power supply and check that the
control unit switches on
Having confirmed the damage on the B71/BCHP, proceed
with its replacement, always following the safety
instructions indicated in paragraph 5, points 1,2,3,4.
9
Initial testing
Disconnect from the mains power supply. The LED DL3
should extinguish.
Perform a complete open manoeuvre and a complete
close manoeuvre and check that the installation functions
correctly under battery power.
Reconnect to mains power and check that the LEDs DL1
and DL3 illuminate.
Check that the DL4 LED is off when the motor is stopped.
Only for B70/1DCHP and B70/1THP control units with
High Speed or Reversible motors: with the leaf moving
at the maximum speed selected, activate the STOP
command, or the sensitive edge, and check that DL4
makes a few rapid flashes, signalling that the voltage
limiter has been activated.
NOTE: If the speed is low, or if the inertia of the sliding
sash is low, the DL4 LED may not even flash.
10
Maintenance
Perform scheduled maintenance every 6 months.
Check cleanliness and function.
If the unit contains dirt, moisture, insects or other foreign
matter, disconnect from mains power and clean the
board and the housing.
Repeat the initial installation test procedure after
cleaning.
If any corrosion is found on the printed circuit board,
evaluate if it is necessary to replace the board itself.
Check battery charge by performing a complete open/
close manoeuvre and measuring the output voltage from
the batteries.
A battery pack in good condition must maintain a
minimum voltage of at least 22V .
Replace the batteries at least every 3 years.
11
Disposal
This product may only be uninstalled by qualified
technical personnel,
procedures for removing the product correctly
and safely. This product consists of numerous
different materials. Some of these materials
may be recycled, while others must be disposed of
correctly at the specific recycling or waste management
facilities indicated by local legislation applicable for this
category of product.
Do not dispose of this product as domestic refuse.
Observe local legislation for differentiated refuse
collection, or hand the product over to the vendor when
purchasing an equivalent new product.
Local legislation may envisage severe fines for the
incorrect disposal of this product.
Warning! Some parts of this product may contain
substances that are harmful to the environment or
dangerous and which may cause damage to the
environment or health risks if disposed of incorrectly.
ROGER TECHNOLOGY is the exclusive proprietor holder
of all rights regarding this publication.
ROGER TECHNOLOGY reserves the right to implement
any modifications without prior notification. Copying,
scanning or any alterations to this document are
prohibited without express prior authorised from by
ROGER TECHNOLOGY.
ROGER TECHNOLOGY CUSTOMER SERVICE:
business hours: Monday to Friday
Telephone no:
E-mail:
Skype:
I the undersigned, as acting legal representative of the
manufacturer
Roger Technology - Via Botticelli 8, 31021 Bonisiolo di
Mogliano V.to (TV)
hereby DECLARE that the appliance described below:
Description: Battery and battery charger
Model: B71/BCHP
Is conformant with the legal requisites of the following
directives:
– 2014/35/UE;
– 2014/30/UE;
– 2011/65/UE
and that all the standards and/or technical requirements
indicated as follows have been applied:
EN 61000-6-3;
EN 61000-6-2;
EN 60335-1
Place: Mogliano V.to
Date: 24-03-2017
following suitable
12
Additional information and contact
details
08:00 to 12:00 - 13:30 to 17:30
+39 041 5937023
service@rogertechnology.it
service_rogertechnology
13
Declaration of Conformity
Signature
11 11