Explanation Of General View - Makita LS0714 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Stopper pin
2 Bolt
3 Adjusting bolt
4 Blade guard
5 Blade guard A
6 Blade guard B (For European
countries)
7 Thumb screw
8 Kerf board
9 Saw blade
10 Blade teeth
11 Left bevel cut
12 Straight cut
13 Turn base
14 Guide fence
15 Top surface of turn table
16 Periphery of blade
17 Adjusting screw
18 Stopper arm
19 Sub-fence
20 Lock lever
21 Miter scale
22 Pointer
23 Grip
24 Lever
25 Release button
26 Bevel scale
27 Arm
28 Screw
29 Lock-off button
30 Switch trigger
31 Handle
32 Light
33 Light switch
SPECIFICATIONS
Model
Blade diameter ................................................................................................................................................... 190 mm
Blade body thickness............................................................................................................................ 1.3 mm – 2.0 mm
Hole (arbor) diameter ............................................................................................................................................ 20 mm
Max. Miter angle .................................................................................................................................. Left 47°, Right 57°
Max. Bevel angle ................................................................................................................................... Left 45°, Right 5°
Max. Cutting capacities (H x W) with blade 190 mm in diameter.
Miter angle
0°
45° (left and right)
57° (right)
(Note)
* mark indicates that a wood facing with the following thickness is used.
1: When using a wood facing 20 mm thick.
2: When using a wood facing 15 mm thick.
3: When using a wood facing 10 mm thick.

Explanation of general view

34 Switch for laser
35 Wrench holder
36 Hex wrench
37 Center cover
38 Hex socket bolt
39 Safety cover
40 Shaft lock
41 Arrow
42 Blade case
43 Outer flange
44 Inner flange
45 Hex socket bolt (left-handed)
46 Spindle
47 Dust bag
48 Dust nozzle
49 Fastener
50 Dust box
51 Cover
52 Button
53 Cylinder part
54 Sawdust
55 Support
56 Vise arm
57 Vise rod
58 Holder
59 Holder assembly
60 Vise knob
61 Projection
62 Vise shaft
63 Base
64 Rod 12
65 Two clamping screws which
secure the slide pole
45° (left)
*45 mm x 265 mm (Note 1)
40 mm x 300 mm
*45 mm x 185 mm (Note 2)
40 mm x 212 mm
—
66 Holder assembly
67 52/38° type crown molding
68 45° type crown molding
69 45° type cove molding
70 Inside corner
71 Outside corner
72 Vise
73 Spacer block
74 Aluminum extrusion
75 Over 15 mm (5/8'')
76 Over 420 mm (16-1/2'')
77 Holes
78 Set plate
79 Cut grooves with blade
80 Triangular rule
81 Arm holder
82 0° bevel angle adjusting bolt
83 Left 45° bevel angle adjusting
84 Workpiece
85 Cutting line
86 Vertical vise
87 Pull out
88 Push
89 Lamp box
90 Screws
91 Fluorescent tube
92 Screwdriver
93 Screw (one piece only)
94 Lens for the laser light
95 Limit mark
96 Brush holder cap
LS0714/LS0714F/LS0714FL/LS0714L
Bevel angle
0°
*60 mm x 265 mm (Note 1)
52 mm x 300 mm
*60 mm x 185 mm (Note 2)
52 mm x 212 mm
*60 mm x 145 mm (Note 3)
52 mm x 163 mm
(optional accessory)
bolt
5° (right)
—
40 mm x 300 mm
—
—
—
15