Makita LS0714 Manual De Instrucciones página 24

2. Bevel angle
1. 0° bevel angle
Push the carriage toward the guide fence and
tighten two clamp screws to secure the carriage.
Lower the handle fully and lock it in the lowered posi-
tion by pushing in the stopper pin. Loosen the lever
at the rear of the tool.
Turn the 0° bevel angle adjusting bolt (lower bolt) on
the right side of the arm two or three revolutions
counterclockwise to tilt the blade to the right.
(Fig. 52)
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
square, etc. by turning the 0° bevel angle adjusting
bolt clockwise. Then tighten the lever securely.
(Fig. 53)
Make sure that the pointer on the arm point to 0° on
the bevel scale on the arm holder. If it does not point
to 0°, loosen the screw which secures the pointer
and adjust the pointer so that it will point to 0°.
(Fig. 54)
2. 45° bevel angle
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm points to
45° on the bevel scale on the arm holder. If the
pointer does not point to 45°, turn the 45° bevel
angle adjusting bolt (upper bolt) on the right side of
the arm until the pointer points to 45°. (Fig. 55)
Adjusting the position of laser line (Fig. 56 & 57)
For model LS0714FL, LS0714L
WARNING:
• As the tool is plugged when adjusting the position of
laser line, take a full caution especially at switch action.
Pulling the switch trigger accidentally cause an acci-
dental start of the tool and personal injury.
CAUTION:
• Never look into the laser beam directly. Direct laser
beam causes damage to your eyes.
• Never apply a blow or impact to the tool. A blow or
impact causes the incorrect position of laser line, dam-
age to the laser beam emitting part or a short life of the
tool.
• Have the tool repaired by Makita authorized service
center for any failure on the laser unit. No change with
different type of laser is permitted.
24
When adjusting the laser line appears on the left side
of the saw blade
1
1 Screw to change the movable range of the adjusting
screw
2 Adjusting screw
3 Hex wrench
4 Laser line
5 Saw blade
005527
When adjusting the laser line appears on the right
side of the saw blade
1
1 Screw to change the movable range of the adjusting
screw
2 Saw blade
3 Laser line
005528
For both adjustments, do as follows.
1. Make sure that the tool is unplugged.
2. Draw the cutting line on the workpiece and place it
on the turn table. At this time, do not secure the
workpiece with a vise or similar securing device.
3. Lower the blade by lowering the handle and just
check to see where the cutting line and the position
of the saw blade is. (Decide which position to cut on
the line of cut.)
4. After decision the position to be cut, return the han-
dle to the original position. Secure the workpiece
with the vertical vise without shifting the workpiece
from the pre-checked position.
5. Plug the tool and turn on the laser switch.
6. Adjust the position of laser line as follows.
The position of laser line can be changed as the movable
range of the adjusting screw for the laser is changed by
turning two screws with a hex wrench. (The movable
range of laser line is factory adjusted within 1 mm from
the side surface of blade.)
To shift the laser line movable range further away from
the side surface of blade, turn the two screws counter-
clockwise after loosening the adjusting screw. Turn these
two screws clockwise to shift it closer to the side surface
of the blade after loosening the adjusting screw.
2
4
3
2
5
3