Daily Maintenance; Weekly Maintenance; Monthly Maintenance; Yearly Maintenance - Husqvarna 130 Mark II Manual De Usuario

product each day. Only do the maintenance work that is
found in this manual. Speak to an approved service
center about other maintenance work not found in this
manual.

Daily maintenance

• Clean the external surfaces.
• Make sure that the throttle trigger lockout and throttle
trigger work correctly.
• Clean the chain brake and make sure that it
operates correctly.
• Examine the chain catcher for damage. Replace the
chain catcher if it is damaged.
• Turn the guide bar daily for more equal wear.
• Make sure that the lubrication hole in the guide bar is
not clogged.
• Remove saw dust and other unwanted material from
below the clutch cover.
• Clean the guide bar groove.
(Fig. 58)
• Make sure that the guide bar and saw chain get
sufficient oil.
• Examine the saw chain for cracks and irregularly
worn rivets and links. If necessary, replace the saw
chain.
• Examine the saw chain for the correct tension and
for burrs on the chain drive links. If necessary,
replace the saw chain.
• Sharpen the saw chain. Refer to
chain on page 19 .
• Examine the drive sprocket for too much wear and
replace if necessary.
(Fig. 59)
• Clean the air intake of the starter housing.
• Make sure that the nuts and screws are tight.
• Make sure that the controls operate correctly.

Weekly maintenance

• Make sure that the cooling system works correctly.
• Make sure that the starter, starter cord and return
spring work correctly.
• Make sure that the vibration damping elements are
not damaged.
(Fig. 60)
• File off any burrs from the edges of the guide bar.
• Clean or replace the spark arrester mesh on the
muffler.
(Fig. 61)
• Clean the external surfaces of the carburetor and its
adjacent areas.
• Clean the air filter. Install a new air filter if it is
damaged or too dirty to be fully cleaned. Refer to
clean the air filter on page 19 for more information.
18
To sharpen the saw
To

Monthly maintenance

• Examine the brake band on the chain brake for
wear. Replace when the brake band thickness is
less than 0.6 mm (0.024 in) at the most worn point.
(Fig. 62)
• Examine the clutch center, clutch drum and clutch
spring for wear.
• Clean the spark plug. Make sure that the electrode
gap is correct.
(Fig. 63)
• Clean the external surfaces of the carburetor and its
adjacent areas.
• Examine the fuel filter and the fuel hose. Replace if
necessary.
• Empty the fuel tank.
• Empty the oil tank.
• Examine all cables and connections.

Yearly maintenance

• Examine the spark plug.
• Clean the external surfaces of the carburetor and its
adjacent areas.
• Clean the cooling system.
• Examine the spark arrester mesh.
• Examine the fuel filter.
• Examine the fuel hose for damage.
• Examine all cables and connections.

Intermittent maintenance

• Have an approved service center repair or replace
the muffler after 50 hours of operation.
• Do maintenance on the spark plug when:
• the power level in the engine is low.
• it is hard to start the engine.
• the engine does not work correctly at idle speed.
• Do a check of the saw chain lubrication each time
To do a check of the saw chain
you refuel. See
lubrication on page 20 .
To adjust the idle speed
Make sure that the air filter is clean and the air filter
cover is attached before you adjust the idle speed.
1. Turn the idle adjustment screw, which is identified
with a "T" mark, clockwise until the saw chain starts
to turn.
2. Turn the idle adjustment screw, which is identified
with a "T" mark, counterclockwise until the saw chain
stops.
3. The idle speed must be below the speed when the
saw chain starts to turn. The idle speed is correct
when the engine operates smoothly in all positions.
862 - 002 - 03.12.2018