Preventive Maintenance; Recommended Spare Parts - CM Hurricane 5623A Manual De Funcionamiento

MAINTENANCE (CONTINUED)
LUBRICATION
If hoist is disassembled for service, repair or inspection, remove
and clean existing grease from unit and replace with approximately
1 oz. of Poliplex 2 (Century Lubricants Co.) grease or equal lubricant
to the exterior surface of the drive shaft, gears, internal thread
of brake hub, surface of liftwheel bushings (1/2 ton unit), bushings
in the gear side plate and gear cover, internal and external surfaces
of handwheel bushings and rim of handwheel cover.
GEARS
The gears (656-12A and 656-12B) do not have to be timed and
as a result, they do not have to be oriented in a certain position
during assembly. However, for proper operation of the 1/2, 1, 3,
5 and 10 ton units, one gear marked "A" and one gear marked
"B" must be used.

PREVENTIVE MAINTENANCE

In addition to the inspection procedures, a preventative
maintenance program should be established to prolong the useful
life of the hoist and maintain its dependability and continued
safe use. The program should include the periodic inspections
with particular attention being paid to the lubrication of various
components using the recommended lubricants (See Figure 7).
TESTING
Prior to initial use, all repaired or used hoists that have not been
operated for the previous 12 months shall be tested by the user
for proper operation.
Test the unit first in the unloaded state and then with a light load
of 100 lbs. times the number of load supporting parts of load chains
to be sure it operates properly and the brake holds the load when
ITEM
Inspector's
Signature
KEY NO.
COMPONENT
(SEE PAGES 13 &14)
656-28 Load Chain
656-11
Gears and Bearing Sur-
656-12
faces of Upper and Lower
656-13
Hook Knobs
656-17
* This lubrication schedule is based on a hoist operating in normal environment conditions. Hoists operating in adverse atmospheres containing excessive heat, corrosive fumes or vapors,
abrasive dust, etc., should be lubricated more frequently.
** See page 13 for ORDERING INSTRUCTIONS.
Figure 7 - Recommended Lubrication Schedule
INSPECTOR'S REPORT
REMARKS (LIST DEFICIENCIES AND RECOMMENDED ACTION)
Date
Inspected
Figure 6 - Recommended Inspector's Report
RECOMMENDED LUBRICATION SCHEDULE*
TYPE OF LUBRICANT
Lubriplate® Bar and
Chain Oil 10-R
Poliplex 2
(ENGLISH)
the hand chain is released; then test with a load of 125% of its
rated capacity.
In addition, hoists in which load sustaining parts have been
replaced must be tested with 125% of rated capacity by or
under the direction of a designated person and a written report
prepared for record purposes.
NOTE: Because this hoist is equipped with a load limiting device
occasional slipping of the handchain wheel may occur when testing
with 125 percent of rated load.
NOTE: For additional information on Inspection and Testing
refer to ASME B30.16,"Overhead Hoists", obtainable from
ASME Order Department, 22 Law Drive, Box 2300, Fairfield, NJ
07007-2300, U.S.A.

RECOMMENDED SPARE PARTS

Pawl Kit
Ratchet Kit
Upper Hook Assembly Kit
Lower Hook Assembly Kit
Upper Latch Kit
Lower Latch Kit
Load Chain
Hand Chain
Alterations or modifications of equipment and use of any parts
other than CM Hurricane 360 manual hoist repair parts can lead
to dangerous operation and injury.
TO AVOID INJURY:
Do not alter or modify equipment. Do use only CM Hurricane 360
provided replacement parts.
Approved by
**ORDER PART NO. TYPE OF SERVICE AND FREQUENCY OF LUBRICATION
HEAVY
28619 (1 gal. can)
Daily
40630 (1 lb. can) When hoist is disassembled for cleaning or repairs
10
Date
NORMAL INFREQUENT
Weekly Monthly
P/N 192048547 Rev. AA January 2018