Change Of Water; Daily Maintenance; Service; Immersion Heater - Hedson W10 Manual Del Usuario

11.

CHANGE OF WATER

After washing 300 wheels, the water must be changed and the
machine cleaned.
PLEASE NOTE: If moving the unit filled with water, the
forklift MUST reach all the way under the machine (see
picture 1) and out on the back (see picture 2). The fork
lift should be entered slightly offset to the right,
measured from the center of it. There is a bulge
beneath the machine on the left side of it which
contains the internal drain gutter.
1. Top up with water until the water level reaches the upper
notch of the red level indicator (see picture 14 and 15).
Place the ShotMediumBasket in the wash room and close
the door. PLEASE NOTE: Place the ShotMedium
Basket with the side opening to the left (see
picture 17).
2. Press the ShotMedium collection button (see chapter 9)
and let the machine run until it stops automatically
(approximately 5 min). Confirm that water level is raised
by pressing ENTER. If needed, run this ShotMedium col-
lecting program twice.
As the ShotMedium is collected in the basket, you can
easily check that you have the correct amount of ShotMe-
dium, by checking that the ShotMedium level reaches the
25kg marking on the side of the basket (see picture 17). If
this is not the case, top up with more ShotMedium.
3. PLEASE NOTE: Always turn off the main switch
before emptying out the water in the machine!
Let the water out by putting the drain hose on the floor
(see picture 3). The waste water from this machine should
be let out through an oil separator. If required, the ma-
chine can be equipped with an environmentally friendly
water cleaning and filtering system. It will separate the
waste and the water, so that the water can be emptied
into the drain. After having used the Hedson Water
cleaning system, the waste water fulfils all water authority
requirements. Please contact your local water authorities
for more information about local limit values.
4. Remove the dirt sediment from the bottom of the machine
with a hand bailer and then rinse the machine.
For improved access, remove the support bar (see picture 7).
PLEASE NOTE: The residues from the machine must
be handled as hazardous waste.
Put the ShotMedium back into the machine by turning the basket
over inside the machine and top up with water until the lower
notch of the red level indicator is reached (see picture 15).
PLEASE NOTE: Always turn off the main switch before
emptying out the water in the machine! The heater
will automatically be turned on again after starting a
wash cycle.
12
W10 & W12
12.

DAILY MAINTENANCE

(see picture 14 and 15)
The water level must be checked daily and adjusted when
needed. The machine will not operate properly if the
water level is wrong. It will wash less efficiently and the risk
of blocking the flush pipes will increase.
Check that no foam develops in the machine. This can happen
if you wash many wheels from cars that have just been cleaned
in automatic car washers. Likewise foam can develop if you
add detergents other than the recommended (see chapter 4) to
the water. Foam will cause malfunction. The machine will
wash less efficiently and the risk of blocking the flush pipes will
increase.
If ShotMedium is spilled on the floor it is absolute vital to
sweep the floor regularly to avoid risk of slippery floor (see
picture 13).
13.

SERVICE

- Before removing the MotorCompartmentCover (see
picture 3), make sure to disconnect the power supply and
the airline supplying compressed air (see picture 4) to the
machine.
- The MotorCompartmentCover (see picture 3) may only
be removed by authorized personnel due to exposure of
moving parts and easy access to electrical parts.
14.

IMMERSION HEATER

(see picture 20)
- The immersion heater default setting is scheduled so
that the water temperature is at operation temperature
between 07:00 and 16:00, Monday to Friday (see chapter
10.5.3).
- The factory setting of the water temperature is 45ºC. This
value may NOT be increased since the water will be too
hot and lead to risk of burning injuries.
- PLEASE NOTE: Always turn off the main switch
before emptying out the water in the machine!
The heater will automatically be turned on again after
starting a wash cycle.
15. QUICKLIFT
Congratulations on choosing one of the quickest lifts available
on the market! The Patent Pending QuickLift lifts up to 60kg
wheels up to loading position in approximately 2-4 seconds
which is faster than all competitors. In fact, it is so easy to work
with that it is a natural feature not only for heavy SUV-wheels,
but for all wheels that goes into the wheel washer.
(OPTIONAL)
230312-EN rev.5 2016-09-21