Sunrise Medical QUICKIE ARGON Manual De Usuario página 7

• Make sure that the attendant only holds the wheelchair
using securely mounted parts (e.g. not on the footrests or
the sideguards).
• When using the lifting ramp make sure that the anti-tip
tubes fitted are positioned outside the danger area.
• Secure your wheelchair on uneven ground or when
transferring (e.g. into a car) by using the brakes.
• If and whenever possible, during a journey in a specially
fitted vehicle for disabled people, vehicle occupants should
use the seats in the vehicle and the appropriate restraint
system. This is the only way to ensure that occupants
will have the maximum protection if there is an accident.
When using safety elements offered by SUNRISE
MEDICAL and using a specially designed safety system,
lightweight wheelchairs can be used as a seat when being
transported in a specially fitted vehicle. (See the Chapter
on "Transportation").
• Depending on the diameter and setting of the castors, as
well as the centre of gravity setting of the wheelchair, the
castors may begin to wobble at high speeds. This can lead
to the castors being blocked and the wheelchair may tip
over. Therefore, please make sure that the castors are
adjusted correctly (see the Chapter "Castors"). In particular,
do not travel on an incline without brakes, travel at a
reduced speed. We recommend that novice users use anti-
tip tubes.
• Anti-tip tubes should prevent the chair tipping over
backwards unintentionally. Under no circumstances
should they take the place of transit wheels, and be used
to transport a person in a wheelchair with the rear wheels
removed.
• When reaching for objects (which are in front of, to the side
or behind the wheelchair) make sure that you do not lean
too far out of the wheelchair, as if you change the centre of
gravity there is a risk of tipping or rolling over. The hanging
of additional load (back pack or similar items) onto your
chair backposts can affect the rearward stability of your
chair, especially when used in combination with recliner
backrests. This can cause the chair to tip backwards
causing injury.
• For thigh amputees you must use anti-tip tubes.
• Before setting off, check that your tyre pressure is correct.
For rear wheels it should be at least 3.5 bar ( 350 kPa).
The max. pressure is indicated on the tyre. The knee-lever
brakes will only work if there is sufficient tyre pressure and
if the correct setting has been made (see the Chapter on
"Brakes").
• If the seat and back sling are damaged, you must replace
them immediately.
• Be careful with fire, in particular with burning cigarettes.
Seat and back slings can be set alight.
• If the wheelchair is subject to direct sunlight for a long
period of time, then parts of the wheelchair (e.g. frame,
legrests, brakes and sideguard) may become hot (>41°C).
• Always make sure that the quick-release axles on the rear
wheels are set properly and lock in. If the button on the
quick-release axle is not pressed in, the rear wheel cannot
be removed.
0505/2/ST-000690645.EMS 1B
Note !
The effect of the knee-lever brake as well as the general driving
characteristics are dependant on tyre pressure. The wheelchair
is significantly lighter and easier to manoeuvre when the rear
wheels are pumped up correctly and both wheels have the
same pressure.
Note !
Make sure that your tyres have sufficient tread! Please note that
you are subject to any and all traffic laws when driving in public
traffic.
Note !
Always be careful with your fingers when working or adjusting
the wheelchair!
The products shown and described in this manual may not be
exactly the same in every detail as your own model. However,
all instructions are still entirely relevant, irrespective of detail
differences.
The manufacturer reserves the right to alter without notice any
weights, measurements or other technical data shown in this
manual. All figures, measurements and capacities shown in this
manual are approximate and do not constitute specifications.
we at sunrIse medIcal have been awarded the Iso
9001 certificate, which affirms the quality of our pro ducts
at every stage, from r & d to production. this product
complies with the standards set forth in eu directives.
optional equipment and accessories are available at extra
charge.
ARGON 7